QI: A closed tank partially filled with water up to a height of 0.9 m having an orifice of diameter 15 mm at the bottom of the tank. The air is pumped into the upper part of the tank. Determine the pressure intensity of head (air) required for a discharge of 1.5 litres's through the orifice. Take Ca = 0.62.

QI: A closed tank partially filled with water up to a height of 0.9 m having an orifice of diameter 15 mm at the bottom of the tank. The air is pumped into the upper part of the tank. Determine the pressure intensity of head (air) required for a discharge of 1.5 litres's through the orifice. Take Ca = 0.62.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3.A horizontal venturimeter with inlet diameter 30 cm and throat diameter 15 cm is used to measure the flow of oil of sp. gr. 0.8. The discharge of oil through venturimeter is 50 litres/s, find the reading of the oil-mercury differential manometer. Take Cd = 0.98
In order to drain the tank faster, a pump is installed near thetank exit. Determine how much power input is necessary toestablish an average water velocity of 4 m/s when the tank isfull at 2 m. diameter is 10cm
A venturimeter of 25 cm inlet diameter and 15 cm throat is laid horizontally in a pipe to measure the flow of oil of 900 kg/m3 density. The reading of a mercury manometer is 30 cm. Calculate the discharge in lit/sec. Take Cd =0.98
Determine the available suction head of the pump that is taking a gasoline at 204°C at a closed tank with a pressure 585 kPa gauge. the specific gravity of gasoline is 0.78 and it’s vapor pressure is 620 kPa absolute. the loss in suction pipe is 0.60 m and the pump center line is located 3.60 m above the gasoline level A. 8.66m B. 3.67m C. 7.66m D. 4.47m
A pump is required to move water at a design discharge of 1m3 /s between reservoirA to reservoir B (see schematic below). The difference in surface water elevations between A and B is10m. The difference in elevation between the surface elevation of A and the center of the first pipe sectionis 2m. The pipe is to be commercial steel with an internal diameter of 35cm. Determine the maximumdistance, LAP, from reservoir A that the pump could be installed without encountering cavitationproblems. Consider minor losses of a sharp-edged inlet. Assume a kinematic viscosity of 1x10-6 m 2/s and a specific weight of 9.79kN/m3 . Assume STP conditions (i.e., Pvapor = 3kPa, Patm=101.3kPa)
A tap discharges water evenly in a jet at a velocity of 2.6 m/s at the tap outlet,the diameter of the jet at this point being 15 mm. The jet flows down vertically in asmooth stream. Determine the velocity and the diameter of the jet at 0.6 m below thetap outlet.
The power of available at the stream flowing a 266 ft^3/s having a total head of 34 ft is a. 765.46 kW b. 456.34 hp c. 851. 11 kW d. 245.01 hp
[Mechanical] A 10cmm diameter external cylindrical mouth peice discharge under head of 4m .determine pressure at discharge and pressure at venocontracta. Cc=0.60 and atmospheric pressure=10.3m of water.
A horizontal Venturimeter with inlet and throat diameters 300 mm and 150 mm respectively is used to measure the flow of water. The reading of differential manometer connected to the inlet and the throat is 20 cm of mercury. Determine the rate of flow. Take Cd = 0.98.
A venturi meter measures the flow of water in a 75mm diameter pipe.The difference of head between the throat and the entrance of the meter is measured by a U tube containing mercury,the mercury being in contact with the water.What should be the diameter of the throat of the meter inorder that the difference in level of the mercury be 250mm when the quantity of water flowing in the pipe is 620dm3/min.Assume the coefficient of discharge of the meter to be 0.97
A pump is required to pump water from a large reservoir to the water tower located 20 m above thereservoir (Figure 1). If 0.03 m3/s of water having a density of 1000 kg/m3is pumped through a 30-mmpipe.a. How much power is required to be delivered to the water by the pump? Consider the flow lossesin the pipe; do the necessary assumptions. b. Determine the efficiency of the pump
A pump has a required NPSH of 3.0 m. Assuming that the pump is elevated at 3.5 m above sea level, determine if cavitation occurs when water at 65°C in an open tank is transported and the velocity in the pipe is 1.5 m/s. Total friction loss is considered negligible in the process.