Q1) The induced voltage of a shunt generator is 254 V. When the machine is loaded, the terminalvoltage drops down to 240 V. Determine the load current, and load power if the armatureresistance is 0.04 Q, and the field circuit resistance is 24 Q. You may neglect armature reactioneffect.[Ans., I=340 A, PL=81.6 KW]Q2) A shunt DC generator whose external characteristic is given by the equation:V.250 - 0.5 1.a) Fill the table below,30I (A)VL(V)510152025b) Based on the table above (part a), plot the extemal characteristics (V1/IL).c) If the generator supplies a load that consumes power of 5 KW, using the extemalcharacteristics you found in part (b) above, find the load resistance.[Ans., R1=11.48 ojNote: You must use a graph paper.

Step 1 Induced voltage E = 254 V Terminal voltage Vt = 240 V Armature resistance Ra = 0.04Ω…

QI) The induced voltage of a shunt generator is 254 V. When the machine is loaded, the terminal voltage drops down to 240 V. Determine the load current, and load power if the amature resistance is 0.04 0, and the field circuit resistance is 24 Q You may neglect armature reaction effect. [Ans., IL=340 A, PL=81.6 KW]

QI) The induced voltage of a shunt generator is 254 V. When the machine is loaded, the terminal voltage drops down to 240 V. Determine the load current, and load power if the amature resistance is 0.04 0, and the field circuit resistance is 24 Q You may neglect armature reaction effect. [Ans., IL=340 A, PL=81.6 KW]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

- A separately excited 4 - pole, 900 rpm wave wound dc generator has an induced emf of 240V at rated speed and rated field current. When connected to a load, the terminal voltage is observed to be 200V. If the armature resistance is 0.2 Ω and the flux per pole is 10 m Wb, compute the armature current and the number of conductors
A 110V shunt generator has a full load current of 100A, shunt field resistance of 55 ohms and constant losses of 500W. If full load efficiency is 88%, find the armature resistance. Assuming voltage to be constant at 110V, calculate the efficiency at half load. Find the load current.
. When a self-excited compound DC generator supplies load, the terminal voltage is not the same as the generated emE Why? a) voltage drop across the armature resistance will reduce the voltage available at the load terminals b) where there is a series field, voltage drop across the series field resistance will reduce the voltage available at the load terminals c) both "a" and "b" d) neither "a" nor "b"
6/ What are the parameters required for the internal characteristics of the DC Generator? a. Terminal voltage (V) and Field current (If) b. Generated EMF (Eg) and Armature current (Ia) c. Terminal voltage (V) and load current (IL) d. Generated EMF (Eg) and Load Current (IL)
A 230 V dc machine has an emf constantand . The field is separatelyexcited and produces 0.01 Wb per pole. for all parts ofthe problem. (a) At what speed does the machine operate as adc generator with rated terminal voltage? (b) At what speeddoes the machine operate as a dc motor with rated terminalvoltage? (c) If an external resistance is added in serieswith the armature circuit, at what speed does the machineoperate as a dc motor with rated terminal voltage? (d) If themotor of part (b) is known to be supplying 10 HP to a coupledmechanical load, determine the rotational losses at the point ofoperation ***Any two branches please do not be late
A 50 kW, 220 V, dc shunt generators has an armature resistance including brushes of 0.026 ohms. If the shunt field resistance is 52 Ω. Find the induced emf at rated load.
A short shunt compound DC generator supplies a load current of 10A at a voltage of 10 volts. If the resistance of armature, shunt field and series field windings are 0.001 ohm, 1 ohm 0.00 ohm respectively. a) Draw the the figure. And find the generated voltage.
Of a shunt excited DC generator, Excitation winding internal resistance Rf = 2.5 Ω Armature winding internal resistance Ra = 0.5 Ω A rheostat has been placed in the excitation circuit to keep the machine's end voltage constant at Va = 30 V. Machine Voltage magnetization induced in the armature while operating at n = 1400 rpm at If = 7 A excitation current It is determined as Ea = 30 V from its characteristic. According to this, a) With peak voltage Va = 30 V, excitation current If = 7 A, power supplied to the load when the speed n = 1400 rpm What is the resistance of the rheostat? b) Spindle revolutions are reduced to n = 1000 rpm. In this case Va = 30 V and Ea = 37 V constant What value should the rheostat be adjusted to keep it? Calculate the power given to the load in this new case.
(Draw the Circuit Diagram) A self-excited shunt generator has a field resistance of 60 ohms. When the generator delivers 6 kW, the terminal voltage is 120 V, while the generated emf is 133 V. Determinethe armature resistance
IV. What are the various losses in an induction motor? On what actors do they depend?
A 150-kW 250-volt compound generator is connected long shunt. If the shunt field resistance is 20 ohms, what is the series field-current at full load? (Ans.: 612.5 A) write diagram, given, etc
A DC shunt generator supplies a load of 27 kW at 210 V through the cables of resistance, R = 126 mΩ. If the field winding resistance, Rf = 62 Ω and the armature resistance, Ra = 35 mΩ, Determine (a) the terminal voltage, and (b) the E.m.f. generated in the armature. The terminal voltage is = The E.m.f generated in armature is =