Question 01: For the infinite slope with a steady state seepage as shown in figure, Calculate: a) The factor of safety against sliding along the soil-rock interface b) The height, H, that will give a factor of safety (FoS) of 3 against sliding along the soil-rock interface B = 29 Y = 17.8 kN/m e = 10 kN/m2 d' = 20° H= 12 m Seepage Rock

Question 01: For the infinite slope with a steady state seepage as shown in figure, Calculate: a) The factor of safety against sliding along the soil-rock interface b) The height, H, that will give a factor of safety (FoS) of 3 against sliding along the soil-rock interface B = 29 Y = 17.8 kN/m e = 10 kN/m2 d' = 20° H= 12 m Seepage Rock

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter15: Slope Stability

Section: Chapter Questions

Problem 15.5P

See similar textbooks

Similar questions

A 9m cut slope is shown in the figure. The unit weight of soil is 17kN/m3. Friction angle and cohesion along the rock surface are 20 degrees and 24kPa respectively. The slope makes an angle of 300 from horizontal and the failure plane is at 150. Determine the developed frictional force on the failure plane.
An infinite slope consists of bed rock inclined at 15° to the horizontal that is covered by 4 m (measured vertically) soil with ?′=10?N/?2, ?′=24° and ?=19.0?N/?3.a. What is the factor of safety of this slope?b. If there is steady state seepage through the soil, with the water table coinciding with the ground level, what would be the factor of safety? Assume ?sat = 19.0?N/?3.
Q.1. Refer to the infinite slope shown in Figure 1. Given: β = 19 ͦ, ɣ = 20 kN/m3 , Ø = 33 ͦ, and c’ = 47 kN/m2 . Find the height, H, such that a factor of safety, Fs = 3.1 is maintained against sliding along the soil-rock interface.
Figure 2 shows a slope with an inclination of : β = 58 ͦ. If AC represents a trial failure plane inclined at an angle θ = 32 ͦ with the horizontal, determine the factor of safety against sliding for the wedge ABC. Given: H = 6 m; ɣ = 19 kN/m3, Ø =21 ͦ, and c’= 38 kN/m2
Consider a slope given below with 10 slices, which has a circular failure surface. Each slice has 5 meters wide, and the weight of each slice was estimated on the basis of average height and a unit weight of soil ? = 16 kN/m3. The shear strength of the soil is assumed to be ? = 20 kPa and ? = 20°. The pertinent data for these ten slices is given in the table below. a) Determine the factor of safety using Janbu’s simplified method by assuming the initial ?? = ?. ?. b) Discuss how the factor of safety (stability of the Slope) will change due to the rainfall. You start to consider what environmental conditions will change first.
A cut slope was excavated in saturated clays as shown in the figure. The soil has a unit weight of 17 kN/m³ and an undrained shear strength cᵤ = 20 kPa. The slope make an angle of 60° with the horizontal. Assume stability number m = 0.185. Slope failure occurs along the plane AC with BC = 8 m. Which of the following most nearly gives the maximum depth in meters up to which the cut could be made?
A cut slope of h= 7m was excavated in a saturated clay with a slope of angle beta = 45 degrees with the horizontal. The Previous explorations showed that a rock layer was located at a depth of 14 m. Given that, c = 60 kN/m² and unit weight = 17 kN / (m ^ 3) . Determine the factor of safety.