Plz help me Quéstion 1Find the value of the currents, 11, 12, 13 flowing clockwise in the first, second and third mesh respectively.1 ohm3 ohm5 ohm5V10V2 ohm4 ohm1.54A, -0.189A, -1.195A-1.5409A, O.1887A, 1.1950A2.5472A, 1.3208A, 1.6981AO 2.34A, -3.53A, -2.23AA Moving to another question will save this response.

In this question we will find mesh currents in each mesh flowing in clockwise direction..

Question 1 Find the value of the currents, 1, 12, 13 flowing clockwise in the first, second and third mesh respectively. wwww 1 ohm 3 ohm 5 ohm 5V 10V 2 ohm 4 ohm O 1.54A, -0.189A, -1.195A -1.5409A, 0.1887A, 1.1950A 2.5472A, 1.3208A, 1.6981A O 2.34A, -3.53A, -2.23A A Moving to another question will save this response.

Question 1 Find the value of the currents, 1, 12, 13 flowing clockwise in the first, second and third mesh respectively. wwww 1 ohm 3 ohm 5 ohm 5V 10V 2 ohm 4 ohm O 1.54A, -0.189A, -1.195A -1.5409A, 0.1887A, 1.1950A 2.5472A, 1.3208A, 1.6981A O 2.34A, -3.53A, -2.23A A Moving to another question will save this response.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter4: Conductor Sizes And Types, Wiring Methods, Wire Connections, Voltage Drop, And Neutral Conductor Sizing For Services

Section: Chapter Questions

Problem 37R

See similar textbooks

Similar questions

Determine the symmetrical components of the three currents ?? = 10 ∠ 0A; ?? =100 ∠ 2500 A; and ?? = 10 ∠ 1100 A.
A three phase,Y connected, 215 V (line to line), 7.5 kW, 60 Hz, three pole IM has the following parameter values in Ohm/phase referred to the statorR₁ = 0.294 Ohm, R₂ = 0.144 Ohm, X₁ = 0.203 Ohm, X₂ = 0.409 Ohm, Xm = 10.25 Ohm.The total friction,windage and core losses may be assumed to be constant at 350 W independent of load. For a slip s = 0.02, compute the followingsa) Stator Currentb) Power Factor(pf)c) Rotor Speedd) Power Output(Shaft)e) Output(Shaft) Torquef) Efficiency(n)
Complete the table below using the Kirchhoff's Laws. Compose the voltage equations. Retain the signs generated by the tracing directions. Show complete table as final answer KVL @ loop A: Z11I1 + Z12I2 = Source1 KVL @ loop B: Z21I1 + Z22I2 = Source2
Transmission and distribution lines are important components of any power system study. Aluminium cable steel reinforced (ACSR) (with steel in the centre – as shown in Figure Q1 is normally chosen instead of copper for transmission Explain: (a)The choice of aluminium instead of copper (b)The need to use and place steel at the core
Using any method, find for the currents I1, 12 and I3.Show the complete solution thank you.
Find the unknown currents, I1, I2, I3, I4 and I5 shown
1. Calculate the reactance of generator G1 (referred to 34.5 kV) and the reactance of generator G2 (referred to 34.5 kV).
Question 2The electrical power supply system of a particular country is made of the following. Draw a single line diagram of the electrical power supply system of the country based on the information below using any computer-aided software. Power supply from an infinite bus bar S connected to bus bar A, through a circuit breaker connected between isolators and a three-phase delta/star solidly earthed transformer T1.Power supply source from a generator G1 connected to bus bar B through a circuit breaker connected between isolators, and a three- phase delta/star solidly earthed transformer T2. power supply sources from two generators G2 and G3. Each of the generators are connected to a reactor. Furthermore, each of the generators connected to a common bus bar C through a circuit breaker connected between isolators and a three-phase star/star solidly earthed transformer T3 and T4 respectively. bus bar F to bus bar A by means of two isolators, one at each end of transmission line L6; bus…
1) Find the Io current? 2)Did you find the VAB line voltage on the loads? 3)Find the line voltage Vca on the voltage sources side?
In the circuit of figure shown in the next slide, threeimpedances are 12 – j10 ohms, 10 + j20 ohms, and 15 + j0ohms, connected between conductors a, b, c and the neutral“n” of a balanced 230 volts, 60 hertz, 3 phase, 4 wire, ABCsystem. Using Van as the reference vector, determine:a. Current in each impedanceb. Neutral current Inc. Readings of wattmeters W1, W2, & W3d. Power in each impedance ..
The resistance and reactance of the single-phase 60Hz transmission line conductors are 8.8 ohm and 10.4 ohm respectively. The transmission line delivers 55MW at a power factor of 0.78 lagging to the load with 50kV receiving end voltage. Determine the following a) The inductance of the transmission line in mH Answer for part 1 b) Sending end power factor Answer for part 2 c) Percentage voltage regulation Answer for part 3 d) Percentage Efficiency Answer for part 4
A single phase line has a resistance 0.001 Ohm/meter with a total length of 50 km. The apparent power S is 100 kVA, the line voltage is 3.3 kV. Calculate the: a. The voltage drop b. Thelinelosses The voltage is stepped up to 11 kV. Calculate: c. The voltage drop d. Thelinelosses