For the system shown in the following figure, draw an impedance diagram in per unit, by choosing 100 KVA to be the base KVA and 2500 V as the base voltage for the generator side. 30KVA 25KVA 2000V jo 2 pul (Gi) Transmenion ine (MI) jo:3pu T2 60 KVA (M2) Gz) 40KVA 25KVA 8000V/4000V jo zpu 42008 2200/7500V jo'15 pu 20KVA jo.25pie jo zpe

For the system shown in the following figure, draw an impedance diagram in per unit, by choosing 100 KVA to be the base KVA and 2500 V as the base voltage for the generator side. 30KVA 25KVA 2000V jo 2 pul (Gi) Transmenion ine (MI) jo:3pu T2 60 KVA (M2) Gz) 40KVA 25KVA 8000V/4000V jo zpu 42008 2200/7500V jo'15 pu 20KVA jo.25pie jo zpe

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.23P: Figure 3.32 shows the oneline diagram of a three-phase power system. By selecting a common base of...

See similar textbooks

Similar questions

With generator conyention, where the current leaves the positive terminal of the circuit element, if P is positive then positive real power is delivered. (a) False (b) True
For the power system in Problem 3.41, the synchronous motor absorbs 1500 MW at 0.8 power factor leading with the bus 3 voltage at 18 kV. Determine the bus I and bus 2 voltages in kV Assume that generators I and 2 deliver equal real powers and equal reactive powers. Also assume a balanced three-phase system with positive-sequence sources.
Three single-phase two-winding transformers, each rated 25MVA,34.5/13.8kV, are connected to form a three-phase bank. Balanced positive-suence voltages are applied to the high-voltage terminals, and a balanced, resistive Y load connected to the low-voltage terminals absorbs 75 MW at 13.8 kV. If one of the single-phase transformers is removed (resulting in an open connection) and the balanced load is simultaneously reduced to 43.3 MW (57.7 of the original value), determine (a) the load voltages Va,Vb, and Vc; (b) load currents Ia,Ib, and Ic; and (c) the MVA supplied by each of the remaining two transformers. Are balanced voltages still applied to the load? Is the open transformer overloaded?
Determine the bus admittance matrix (Ybus) for the three-phase power system shown in Figure 6.23 with input data given in Table 6.11 and partial results in Table 6.12. Assume a three-phase 100 MVA per unit base. TABLE 6.11 Bus input data for Problem 6.20 TABLE 6.12 Partially Completed Bus Admittance Matrix (Ybus) for Problem 6.30
While the instantaneous electric power delivered by a single-phase generator under balanced steady-state conditions is a function of time havi ng two components of a constant and a double-frequency sinusoid, the total instantaneous electric power delivered by a three-phase generator under balanced steady-state conditions is a constant. (a) True (b) False
The three-phase power and line-line ratings of the electric power system shown in Figure-1 are given below: G1:82 MVA 30 kV X=10% T1:72MVA 30/300 kV X=11% T2:72MVA 300/30 kV X=11% M:62MVA 25 kV X=9% 300 kV Z= 89+j179 Apply the knowledge of per unit system on above network and draw an impedance diagram showing all impedances in per unit when Sb =100MVA and Vb = 30 kv
A 6,600V, 1,200 kVA, 3-phase alternator is delivering full load at 0.80 power factor lagging. Its reactance is 25% and resistance is negligible. By changing its excitation, the emf is increased by 30%. At this load, determine the new current and power factor. Draw the single line diagram.
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
In the above figure, a single line model of a three-phase power system is given. Base power 50MVA, base voltage 13.8kV according to its value, a) Per-unit values of power system circuit elements according to the given base power and base voltage values. calculate. b) The perunit you calculate by drawing the equivalent impedance circuit for one phase of the power system given in the figure. show on the values.
The single line diagram of a power system is shown below. Load represented as impedance, (13.2) kV voltage It draws 60 MVA power from the system when it is below and (0.9) back power factor. Generators and transformers The related electrical parameters are given below. According to this; a) Calculate all impedances in this given circuit in pu and draw the equivalent impedance diagram of the circuit. (Select the base values as 100 MVA and 13.8 kV.) b) Since the voltage values of the generators are given as E1=1.1∟0° pu and E2=1.25∟10° pu, Calculate the value of the voltage (V1).
Refer to the 5-bus data given below. Sbase = 400 MVA, the base voltage is 15.0 kV for buses 1 and 3, and 345 kV for buses 2, 4, 5. Note that 1-5 and 3-4 are 15/345 kV transformers.a) Draw a one-line diagram of the power system.b) Find the elements Y23, Y43, Y11 Y33 of the system bus admittance matrix.
The one line diagram of a three phase power system is as shown in Figure 7 Impedances are marked in per unit on a 100 MVA, 400 kV base The load at bus 2 is S2 15.93 MW - j 33.4 MVar, and at bus 3 is S3 77 MW + j 14 MVar It is required to hold the voltage at bus 3 at 400 kV Working in per unit, determine the voltage at buses 2 and 1