QUESTION 1. A hydrazine tank, designed by Orbital Propulsion Center, is made of T16A14VSTA (3.7164.7) titanium alloy is shown in the figure.a. The length of the tank is 890 mm and its volume is 176.5 liters. Calculate the radius of thetank.b. Determine the tank thickness, t such that the tank resists the proof pressure of 36.9 Barwithout permanent deformation and the burst pressure of 49.2 Bar without fracture.c. Under the operational conditions (MEOP), determine the absolute maximum shear stressthat occurs on the tank.http://www.space-propulsion.com/spacecraft-propulsion/hydrazine-tanks/index.htmlSurface Tension Propellant Tank OST 33/0Net Volume Range176.5 LitresPropellantsHydrazine (N,H)Spherical with a gylindrical IntersectionGeometrical ShapeMaximum Expected OperatingPressure (MEOP)24.63 barProof Pressure (1.5 x MEOP)36.95 barBurst Pressure (2.0 x MEOP)49.26 barInterface Fixation4 Suspension TrunnionsMaterials- Pressure VesselTIGAIAV STA (3.7164.7)- Trunnions / PortsTI6AI4V (3.7164.1)TIGAI4V (3.7164.1)- PMDTank Mass RangeProject Involvement13.5 kgCosmo / SkyMed

Dear, As per norms, i am answering first part of question, kindly repost the question for remaining…

QUESTION 1. A hydrazine tank, designed by Orbital Propulsion Center, is made of Ti6A14V STA (3.7164.7) titanium alloy is shown in the figure. a. The length of the tank is 890 mm and its volume is 176.5 liters. Calculate the radius of the tank. b. Determine the tank thickness, t such that the tank resists the proof pressure of 36.9 Bar without permanent deformation and the burst pressure of 49.2 Bar without fracture. c. Under the operational conditions (MEOP), determine the absolute maximum shear stress that occurs on the tank.

QUESTION 1. A hydrazine tank, designed by Orbital Propulsion Center, is made of Ti6A14V STA (3.7164.7) titanium alloy is shown in the figure. a. The length of the tank is 890 mm and its volume is 176.5 liters. Calculate the radius of the tank. b. Determine the tank thickness, t such that the tank resists the proof pressure of 36.9 Bar without permanent deformation and the burst pressure of 49.2 Bar without fracture. c. Under the operational conditions (MEOP), determine the absolute maximum shear stress that occurs on the tank.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.10 ksi. Determine the hoop stress in the wall of the tank.
In inserting an aluminum piston into a steel cylinder, it is given that the inside diameters of the cylinder and of the piston are 0.500 m and 0.4998 m, respectively, at 25OC. The temperature to which they are heated to obtain a perfect fit is 55.8 degrees celsius. Show the solution.
What is press vessels?Application of plane stresses in pressure vessels. Please explain briefly
! Show Full Solution ! *using Thermal Stress Formula *use GIVEN DATA BELOW
Q#1: The strength of the longitudinal joint is 25 kips/ft, whereas for the girth joint it is 20 kips/ft. Calculate the maximum diameter of the cylindrical tank if the internal pressure is 120 psi. Also discuss the joint strength and diameter of tank requirement for the given conditions. SIR, PLS GIVE ME PROPER AND CORRECT ANSWER. THANKS
A thin-walled hollow sphere 3.8 m in diameter holds helium gas at 1767 kPa. Determine the minimum wall thickness of the sphere in mm if its allowable stress is 84.8 MPa.
A scuba tank has a cylindrical body and a spherical end-cap each of 7.5 inches in outer diameter. The wall thickness of the tank is 0.5 inches. The tank is made of aluminum alloy which has an ultimate tensile strength of 56 ksi. Determne the factor of safety against the bursting when the tank is pressurized to 3000 psi. Draw the FBD.
The wall thickness of a 1.2 m diameter spherical tank is 1.6875 mm. Calculate the allowable internal pressure if the stress is limited to 55 MPa. If i will get the same answer again I will report and downvote.
The pressure tank shown is fabricated from 1/8-in steelplate. Calculate the allowable internal pressure if thecircumferential and longitudinal stresses are limited to20 ksi and 10 ksi, respectively.Answer: p= ___________________
Please spicify the given, objectives, solution and summary. A spherical pressure vessel has a 1.5-ft inner radius and 3/16-in. wall thickness. If the working tensile stress of the material is 6000 psi, determine the maximum allowable internal pressure.
What will be the maximum weight of cylinder that can be put as shown in the figure below if the maximum stress at cable is 104 mPa. Round off your answer in two decimal places. This is my third time asking, all answers were wrong....please help
41.) A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa. Towhat value may the internal pressure be increased if the stress in the steelis limited to 100 MPa?