Question 2 A wooden block of mass 6 kg resting on a horizontal plane is pulled by force Q inclined 30° to the horizontal with respect to the positive x-axis. i. Draw a free body diagram for the block What is the minimum value of Q required to start sliding if u=0.3 and µ=0.35. Determine the value of maximum friction between the pair of surfaces Determine the value of kinetic friction ii. ii. iv.

Question 2 A wooden block of mass 6 kg resting on a horizontal plane is pulled by force Q inclined 30° to the horizontal with respect to the positive x-axis. i. Draw a free body diagram for the block What is the minimum value of Q required to start sliding if u=0.3 and µ=0.35. Determine the value of maximum friction between the pair of surfaces Determine the value of kinetic friction ii. ii. iv.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.23P: The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of...

See similar textbooks

Similar questions

Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The 60-lb plank rests on a frictionless roller at A, and the 20-lb triangular support BD. Both bodies are homogenous. The coefficients of static friction are 0.4 at B and 0.3 at D. Determine the largest force P that can be applied to the plank without initiating motion.
Find the largest value of b/h at which the folding table is in equilibrium. The coefficients of static friction are 0.5 at A and 0.3 at C. Neglect the weight of the table.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
SITUATION 2: A packing crate of mass 40 kg is pulled by a rope as shown. Knowing that the coefficient of static friction between the crate and the floor is 0.35, answer the following questions: 4. If α = 40°, determine the magnitude of the force P required to move the crate, in N. (ANSWER: 139) 5. If the crate must be moved to the left along the floor without tipping, determine the largest allowable value of α in degrees. (ANSWER: 58)
Problem 4. A.) If the uniform concrete block has a mass of 500 kg, determine the smallest horizontal force P needed to movethe wedge to the left. The coefficient of static friction between the wedge and the concrete and the wedge and the floor is 0.3. The coefficient of static friction between the concrete and floor is 0.5.ANSWER: P=1797.52; N=1.80kNB.)Refer to problem number 4. Calculate the followinga.) the angle of friction between the wedge and the concrete and the wedge and the floor.Answer: ?????? ??? ????????= ?????? ??? ?????= 16.7ob.) the coefficient of static friction between the concrete and floor.Answer: ????????? ??? ?????= 263.56o
The friction tongs shown in Figure are used to lift a 350 kg casting. Knowing that h = 864 mm, determine the smallest allowable value of the coefficient of static friction between the casting and blocks D and D’.
The slender, uniform bar BC with a mass of 6 kg rests on the center of the 300x200 mm block of mass 3 kg. The friction coefficients at the contact points are: μA = 0.4; µB = 0.6; µC = 0 . Determine the greatest moment M that can be applied to the bar without generating movement in it.
The main body of the cabinet weighs 15 kg, while the upper rectangular portion weighs 2.5 kg. Assume the following values for coefficients of friction between the cabinet and the floor: μs = 0.26 and μk = 0.19. Knowing that the force P applied by Joey’s shoulder to the cabinet is horizontal: If Joey’s horizontal leaning force is 44.5 N, which of the following best describes the motion of the cabinet? slipping, not moving, tipping, or impending to slip?
PLLLSS ANSWER WITHIN AN HOUR The spool in the given figure weighs 25 N, and its center of gravity is located at the geometric center. The weight of block C is 50 N. The coefficients of static friction at the two points of contact are as shown. Determine the largest horizontal force P that can be applied without disturbing the equilibrium of the system.
A safety device used by workers climbing ladders fixed to high structuresconsists of a rail attached to the ladder and asleeve that can slide on theflange of the rail. A chain connects the worker’s belt to the end of aneccentric cam that can be rotated about an axle attached to the sleeve at C.Determine the smallest allowable common value of the coefficient ofstatic friction between the flange of the rail, the pins at A and B, and theeccentric cam if the sleeve is not to slide down when the chain is pulledvertically downward.