Question 2:- For the quarter curve with 60 m wide as shown in fig. below. Determine the vertical and horizontal forces on the curve and the position of center of pressure which the resultant pass on. 30m P.=0 25m | СР CP Water

Question 2:- For the quarter curve with 60 m wide as shown in fig. below. Determine the vertical and horizontal forces on the curve and the position of center of pressure which the resultant pass on. 30m P.=0 25m | СР CP Water

Name: Question 2:- For the quarter curve with 60 m wide as shown in fig. be
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Question 2:- For the quarter curve with 60 m wide as shown in fig. below. Determinethe vertical and horizontal forces on the curve and the position of center of pressurewhich the resultant pass on.30mPa=025m |Water

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
A semicircular 40-ft-diameter tunnel is to be built under a 150-ft-deep, 800-ft-long lake. Determine the total hydrostatic force acting on the roof of the tunnel.
EMERGENCY!!!! The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation of the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the lid (D = 4 m). If the weight of the lid is neglected, it is necessary to keep the lid in balance. Find the size of the force (Fa) required, as shown. Take the density of the water as 999 kg / m3.
A triangular wooden body (S=0.80) is placed in water in theposition indicated in the figure. If the width of the body is 7.0 m,determine if the same for this position is stable or not indicating themetacentric height (YM).
When calculating the value of the force exerted by the water on the window of the dam. Explain why if the pressure varies from the surface of the water, the lower limit for the integral is taken from depth "a" and not from zero? (it is convenient that you make diagrams to support your answer).
EMERGENCY!!!! The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation for the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the cover (D = 4 m). Find the magnitude of the applied force (Fa) as shown.
A semicircular gate with a diameter of 6 ft is installed at 50º as shown below. The top of the gate is 5 ft below the water surface. Determine the resulting hydrostatic force and the location of the center of pressure on the gate.
An oil tanker 3m wide 2 m deep and 10 m long contains oil of density 800 kg/m3, if the tanker is closed and completely filled with the oil and accelerated horizontally at 3m/s2. a.) determine the total liquid thrust (hydrostatic force) on the front end. (in kN) b.) determine the total liquid thrust (hydrostatic force) on the rear end. (in kN)
The distance between the two plates, which are 2 m x 2 m in size and parallel to the earth surface, is 9 mm, and there is water at 20 ° C between them. Find the force in (N) to be applied to pull the top plate to the right at 10 m / s.
The tank of water in Fig. is 12 cm wide into the paper.If the tank is accelerated to the right in rigid-body motion at6.0 m/s 2 , compute ( a ) the water depth on side AB and ( b ) thewater-pressure force on panel AB . Assume no spilling.
Determine the location of the total hydrostatic force from thr bottom surface and the top surface acting on the 2m x 4m gate shown on the illustration.
The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation of the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the cover is D = 4 m. Find the magnitude of the applied force (Fa) as shown. Take the density of water as 999kg / m3.