Question 2: For the system given below (left), find the equivalent torsional system (equivalent inertia and rotational spring constant) shown below (right). The rod and the spring have distributed inertia and mass, respectively. The cylinder makes only rotational movement of 0. Assume all motions to be small. IG Kt Is lea k,m Krea M T7TTTTT ||

Question 2: For the system given below (left), find the equivalent torsional system (equivalent inertia and rotational spring constant) shown below (right). The rod and the spring have distributed inertia and mass, respectively. The cylinder makes only rotational movement of 0. Assume all motions to be small. IG Kt Is lea k,m Krea M T7TTTTT ||

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.15P: In Sample Problem 5.5, determine Oy with one scalar equilibrium equation.

See similar textbooks

Similar questions

b) What is radius of gyration and its importance in designing of a system?
02] Explain the working principle of Kater’s Pendulum and it function in different systems. What is radius of gyration and its importance in designing of a system?
A flywheel with moment of inertia 0.8kgm2 rotates with a speed corresponding to 8 revolutions per second. What is the rotational kinetic energy of the flywheel?
1.A rotor has an inner radius of 10.0 cm and an outer radius of 25.0 cm. It is fixed to a frictionless axle that goes through its center. The moment of inertia (I) of the rotor is 0.0235 kg m2. A set of 5 constant forces act on the rotor, as shown in the diagram below. (a) Find the net torque acting on the rotor, in units of Nm. Be sure to give both the magnitude and direction. (b) Find the angular acceleration of the rotor, in units of rad/s2. Give both the magnitude and direction. (c) Assuming it starts from rest at t = 0, how long does it take for the rotor to reach an angular speed of 565 revolutions pre minute (rpm)? Give your answer in seconds. (d) At t = 2.50 seconds, how many complete revolutions will the rotor have made?
Consider a pulley system shown below. Assume there is no slip between the cord and the pulley. I is the mass moment of inertia of the pulley about its own centroidal axis. Find the equations of motion in terms of x. Select all that apply.
J1. In summary, the rotational acceleration of the rollers is 44.02 rad/s2. Using the mass moment of inertia found in step 5, what is the torque required to accelerate the rollers?
A disk-shaped platform has a known rotational inertia. The platform is mounted on a fixed axle and rotates in a horizontal plane, as shown above. A student wishes to determine the frictional torque exerted on the platform by the axle as the platform rotates. The student has access to equipment that would usually be found in a school physics laboratory. a. Describe an experimental procedure the student could use to collect the data needed to find the frictional torque exerted on the platform while it rotates. What quantities would be measured? What equipment would be used for the measurements, and how would that equipment be used? Describe the overall procedure to be used, including any steps necessary to reduce experimental uncertainty. Give enough detail so that another student could replicate the experiment. b. Describe how the data from the measurements could be analyzed to determine the frictional torque exerted on the rotating platform. It is often assumed that the…
A steel shaft of 0.05 m diameter and 2 m length is fixed at one end and carries at the other end a steel disc of 1 m diameter and 0.1 m thickness. Find a) the mass of the disc and its moment of inertia about the axis of the shaft, b) the stiffness of the steel shaft and c) the system’s natural frequency of torsional vibration.
A gyroscope is precessing about a vertical axis. What happens to the precession angular speed if the following changes are made, with all other variables remaining the same? (a) The angular speed of the spinning flywheel is doubled; (b) the total weight is doubled; (c) the moment of inertia about the axis of the spinning flywheel is doubled; (d) the distance from the pivot to the center of gravity is doubled. (e) What happens if all of the variables in parts (a) through (d) are doubled? In each case justify your answer.
Consider a pulley system shown below. The coordinate x is the displacement of G. Assume there is no slip between the cord and the pulley, and disk and the ground. What is the kinetic energy of the system? Select all that apply. I don't know how to get these answers.
FOR FIG REFER THE ATTACHED IMAGE The shaft is massless. A thin attached triangular mass ‘m’ is mounted on the shaft. Rotational speed of the shaft is ω. Neglect weight effect of attached mass. Bearings are at A and B. Take Z- axis along the shaft axis. X- axis is vertically downward. Y – axis is horizontal. Take origin at mid-point on the shaft. Question: Under what practical condition can we justify the neglecting of weight of the attached triangular body?
An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number. An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number.