Question 2: The acceleration function of an object doing curvilinear motion is a = {(-0.2r)i+2j+1.5k} m/s², where t is in s. If its initial velocity vo 8i m/s, and initial position is at the origin, determine the magnitude of its velocity when t = 3 s. (a) 2.57 m/s (c) 14.7 m/s (b) 4.06 m/s (d) 10.3 m/s

Question 2: The acceleration function of an object doing curvilinear motion is a = {(-0.2r)i+2j+1.5k} m/s², where t is in s. If its initial velocity vo 8i m/s, and initial position is at the origin, determine the magnitude of its velocity when t = 3 s. (a) 2.57 m/s (c) 14.7 m/s (b) 4.06 m/s (d) 10.3 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The speed of an aircraft is given to be 950 km/h. If the speed of sound at that location is 315 m/s, the Mach number is (a) 0.63 (b) 0.84 (c) 1.0 (d) 1.07 (e) 1.20
A mass m = 1.0 kg moves under the action of the force given by F = 2i + 6tj, where t is in seconds. Yes, at t = 0 the mass starts from rest from the origin, determine (a) its acceleration, velocity and position as functions of t, (b) its linear momentum p, angular momentum L, as functions of t, (c) evaluate the previous sections for t = 2 s.
Distilled water flowing with a flow rate of 50.2 L / min in the venturimeter with a narrow section of 8.6x10^-5m^2 and a wide section of 6.88x10^-4 m^2 transitions from wide to narrow section. The pressure in the wide cross-section of water at 200C is 0.8 bar and tell whether cavitation will occur. (Contraction Loss = KdV22 / 2g and Kd = 0.35) (Vapor pressure values are given in the table below.)
A pitot-static tube to be used in 2n airplane for on-flight measurement was calibrated on ground by using air of density 1.20 kg/m? . A measurement taken at an altitude of 3000 m where the ambient pressure and density were 70 kPa (abs) and 0.91 kg/m? respectively, indicated a velocity of 200 m/s by using the above ‘ground level calibration. Estimate the true speed of the airplane [Take k = 1.4 2nd R = 287 J(kg K
The flow rate of ammonia with mass density of 624.6 kg/m^3 and viscosity of 1.697 x 10^-4 kg/m-s, through a 2 cm diameter pipe is to be measured with 1.5 cm diameter flow nozzle equipped with differential pressure gage. If the gage reads a pressure differential of 4 kPa. determine the velocity of ammonia through the pipe in m/s if Cd= 0.96. a.4.34 b. 8.34 c.2.34 d. 6.34 With FBD
Pressure cookers, in general, maintain a gage pressure of 2 atm (or 3 atm absolute) inside. Therefore, pressure cookers cook at a temperature of about 133°C instead of 100°C, cutting the cooking time by as much as 70 percent while minimizing the loss of nutrients. The newer pressure cookers use a spring valve with several pressure settings rather than a weight on the cover. A certain pressure cooker has a volume of 6 L and an operating pressure of 75 kPa gage. Initially, it contains 1 kg of water. Heat is supplied to the pressure cooker at a rate of 500 W for 30 min after the operating pressure is reached. Assuming an atmospheric pressure of 100 kPa, determine the temperature at which cooking takes place.
Pressure cookers, in general, maintain a gage pressure of 2 atm (or 3 atm absolute) inside. Therefore, pressure cookers cook at a temperature of about 133°C instead of 100°C, cutting the cooking time by as much as 70 percent while minimizing the loss of nutrients. The newer pressure cookers use a spring valve with several pressure settings rather than a weight on the cover. A certain pressure cooker has a volume of 6 L and an operating pressure of 75 kPa gage. Initially, it contains 1 kg of water. Heat is supplied to the pressure cooker at a rate of 500 W for 30 min after the operating pressure is reached. Assuming an atmospheric pressure of 100 kPa, determine the amount of water left in the pressure cooker at the end of the process.
8.a. When a machine is tested, the volume of cooling air is 1250 cfm. If the temperature of the entering air is 25 C and the temperature of the outgoing air is 35 C, the loss in the machine isA. 7.1 kw.B. 24.8 kw.C. 12.5 kw.D. 17.7 kw. 8.b. When a motor is tested with a prony brake, the scale reading is 3.50 lb. The length of the brake arm is12 in. and its weight is 0.50 lb. If the motor speed is 1700 rpm and the power input is 1050 watts, themotor efficiency isA. 80.5%B. 69%C. 75%.D. 64.5%.
2.8 The setup shown provides a liquid flow through the tissues for a physiological experiment. Taking readings h1(t) and h2(t), develop an expression for the storage rate of the liquid in the tissue. Identify your choice of control volume very carefully.
As a young engineer, you have been tasked to select the location of a wind turbine based on the details of the location and relevant specification below:Air densityAverage air velocityDiameter of wind turbine bladesLOCATION A1.29 kg/m3 54 km/h 70 mLOCATION B1.21 kg/m3 63 km/h 60 m By comparing the amount of power generated (in MW) at Location A and Location B, determine the location that will give the optimum wind power generation.9 kg of Refrigerant 134-a is initially at 26.69°C with enthalpy of 100 kJ/kg. Heat is transferred to the refrigerant under a constant-pressure process until the entropy of the refrigerant reaches 0.9795 kJ/kg.K.(i) Determine the final temperature of the refrigerant(ii) Calculate the boundary work, Wb, in kJ.Assist your answer with a proper P-v diagram indicating the properties,process, and boundary work region clearly.(iii) Explain the reason behind the high amount of boundary work obtained in (ii).Assist your explanation with relevant sketching.
State the first law of thermodynamics and prove that for a non-flow process, it leads to the energy equation Q= Delta U+W.
Radiation heat transfer occurs at a speed of: (a) Sound (b) Light (c) 60,000 km/hr (d) 350 m/s