Question 4 A shaft of 75 mm diameter fails (experiences the onset of yield) under a bending moment of 2.5 kNm. A similar shaft is exposed to a direct bending moment of 1.5 kNm, a torsional load of 0.75 kNm and a direct load (F) of undetermined magnitude. Use the Tresca Criterion to determine the maximum direct load the second shaft can carry before failure (onset of yield).

Question 4 A shaft of 75 mm diameter fails (experiences the onset of yield) under a bending moment of 2.5 kNm. A similar shaft is exposed to a direct bending moment of 1.5 kNm, a torsional load of 0.75 kNm and a direct load (F) of undetermined magnitude. Use the Tresca Criterion to determine the maximum direct load the second shaft can carry before failure (onset of yield).

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.2.15P: -15 A composite beam is constructed froma wood beam (3 in. x 6 in.) and a steel plate (3 in, wide)....

See similar textbooks

Similar questions

A two-axle carriage that is part of an over head traveling crane in a testing laboratory moves slowly across a simple beam AB (sec figure). The load transmitted to the beam from the front axle is 2200 lb and from the rear axle is 3800 lb. The weight of the beam itself may be disregarded. Determine the minimum required section modulus S for the beam if the allowable bending stress is 17,0 ksi, the length of the beam is 18 ft, and the wheelbase of the carriage is 5 ft. Select the most economical I-beam (S shape) from Table F-2(a), Appendix F.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
-15 A composite beam is constructed froma wood beam (3 in. x 6 in.) and a steel plate (3 in, wide). The wood and the steel are securely fastened to act as a single beam. The beam is subjected to a positive bending moment M. = 75 kip-in. Calculate the required thickness of the steel plate based on the following limit states: Allowable compressive stress in the wood = 2 ksi Allowable tensile stress in the wood = 2 ksi Allowable tensile stress in the steel plate = 16 ksi Assume that Ew= 1,500 ksi and es= 30,000 ksi.
The bar shown, made from ground steel (Sy = 36 ksi, Sut = 57 ksi), is subjected to a fully reversed bending moment of 30 lb.ft. Calculate the corrected endurance limit for a 90% reliability. The bar will be used at a temperature of 550 oC. Select one: a. Se = 11.83 ksi b. Se = 10.20 ksi c. Se = 13.44 ksi d. Se = 8.55 ksi
A 21 feet steel line shaft has no bending action except its own weight. What power in hip can the shaft deliver at a speed of 360 rpm? Consider that the torsional deflection will not exceed 0.08 degree per ft length.
A 16 ft steel line shaft has no bending action except its own weight. What power in hp can shaft deliver at a speed of 200 rpm. Consider that the torsional deflection wm not exceed 0.08o/ft of length.
Problem: 1 A line shaft rotating at 55 RPS is to transmit 28 kW. The shaft may be assumed to be made of mild steel with an allowable shear stress of 85 MPa. Determine the diameter of the shaft, neglecting the bending moment on the shaft.
rotating shaft of 16 mm diameter is made of plain carbon steel. It is subjected to axial load of 5000 N, a steady torque of 50 N-m and maximum bending moment of 75 Nm. Calculate the factor of safety available based on 1. Maximum normal stress theory; and 2. Maximum shear stress theory. Assume yield strength as 400 MPa for plain carbon steel
Since the allowable normal stress of AC beam loaded with uniformly distributed load is 100MPa in tension, 120MPa in compression and 50MPa in shear stress, check whether the beam is safe.
Please give proper and step by step solution. solid circular shaft is subjected to a bending moment of 300 kNm, a twisting moment of 125 kNm. If the yield stress of the shaft material is 350 N/mm², determine the diameter of the shaft according to the maximum shearing stress theory of failure.
A forged steel bar, 50 mm in diameter, is subjected to a reversed bending stress of 250 MPa. The bar is made of 40 C8 with ultimate strength of 600 MPa. Calculate the endurance limit and life of the bar. Consider 90% reliability.
A solid circular shaft has a diameter of d mm and is made from steel, which fail when tested in simple tension test at a stress of 150 MPa. The shaft was subjected by bending moment and torque which are 22.2 kNm and 44.4 kNm respectively. Calculate the minimum allowable shaft diameter, d according to:- (a) Tresca failure criterion (b) Von Mises theory of elastic failure