AWT305 x 41 standard steel shape is used to support the loads shown. Assume w = 46 kN/m, LAB = 1.2 m, LBC = 2.4 m, and LCD = 1.2 m. Consider the entire 4.8 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). B LAB LBC LCD WT305 x 41 Answer: MPa (a) Omax,T MPa (b) Omax,C

AWT305 x 41 standard steel shape is used to support the loads shown. Assume w = 46 kN/m, LAB = 1.2 m, LBC = 2.4 m, and LCD = 1.2 m. Consider the entire 4.8 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). B LAB LBC LCD WT305 x 41 Answer: MPa (a) Omax,T MPa (b) Omax,C

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.10.4P: A weight W = 20 kN falls through a height h = 1,0 mm onto the midpoint or a simple beam of length L...

See similar textbooks

Similar questions

A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
-15 A composite beam is constructed froma wood beam (3 in. x 6 in.) and a steel plate (3 in, wide). The wood and the steel are securely fastened to act as a single beam. The beam is subjected to a positive bending moment M. = 75 kip-in. Calculate the required thickness of the steel plate based on the following limit states: Allowable compressive stress in the wood = 2 ksi Allowable tensile stress in the wood = 2 ksi Allowable tensile stress in the steel plate = 16 ksi Assume that Ew= 1,500 ksi and es= 30,000 ksi.
A weight W = 20 kN falls through a height h = 1,0 mm onto the midpoint or a simple beam of length L = 3 m (see figure). The beam is made of wood with square cross section (dimension don each side) and E = 12 GPa. If the allowable bending stress in the wood is °aLLow =10MPa, what is the minimum required dimension
A fixed-end b earn is subjected to a point load at mid-span. The beam has a rectangular cross section (assume that the h/b ratio is 2) and is made of wood (E = 11GPa). Find height h of the cross section if the maximum displacement of the beam is 2 mm. Calculate the displacement of the beam at the inflection points.
Beam ACB hangs from two springs, as shown in the figure. The springs have stiffnesses Jt(and k2^ and the beam has flexural rigidity EI. What is the downward displacement of point C, which is at the midpoint of the beam, when the moment MQis applied? Data for the structure are M0 = 7.5 kip-ft, L = 6 ft, EI = 520 kip-ft2, kx= 17 kip/ft, and As = 11 kip/ft. Repeat part (a), but remove Af0 and instead apply uniform load q over the entire beam.
Since the allowable normal stress of AC beam loaded with uniformly distributed load is 100MPa in tension, 120MPa in compression and 50MPa in shear stress, check whether the beam is safe.
A steel tee shape is used to support the loads shown on the beam in Fig. P8.21a. The dimensions of the shape are shown in Fig. P8.21b. Consider the entire 24-ft length of the beam and determine: the maximum tension bending stress at any location along the beam, and the maximum compression bending stress at any location along the beam.
A simply supported beam has a concentrated load at the centre which fluctuatesfrom a value of P to 4 P. The span of the beam is 500 mm and its cross-section is circular with adiameter of 60 mm. Taking for the beam material an ultimate stress of 700 MPa, a yield stress of 500 MPa, endurance limit of 330 MPa for reversed bending, and a factor of safety of 1.3, calculate the maximum value of P. Take a size factor of 0.85 and a surface finish factor of 0.9.
What is the max bending stress in ksi about the x axis for a W12x50 beam with a 43.6 k-ft max moment? Provide 2 decimals
A 6 ft long 2” x 12” beam is subjected to a uniform (edge-to-edge) distributed load of 1500 lbs per linear foot. The material has a Young's Modulus E=2,000,000psi. If the allowed bending stress is 2000 psi, the allowed deflection is L/360 and the allowed shear stress is 250 psi: Is the beam safe in bending? Is the beam safe in deflection for L/360, ( deflDIST = (5 w L4)/(384 E I)? Is the beam safe in shear?
A simply supported beam is subjected to a uniform service dead load of 1.2 kips/ft (including the weight of the beam), a uniform service live load of 1.8 kips/ft. The beam is 40 feet long, and it has continuous lateral support. If A992 steel is used, and the live load deflection must not exceed L/360, Is a W30 x 99 adequate? (for moment, shear, and deflection).
need asap :(A 5-m cantilever beam supports a uniformly distributed load equal to 25 kN/m applied throughout the beam. What is the maximum flexural stress if the beam has a triangular cross-section with b = 300 mm and h = 600 mm? (in MPa)