QUESTION 4 The column in Fig. 4 is constructed from high-strength concrete and six steel reinforcing rods. If it is subjected to an axial force of 150 kN, determine the average normal stress in the concrete and in each rod. Each rod has a diameter of 23 mm. Est = 215 GPa, Ec = 30 GPa. 100 mm- 150 kN 1.2 m

QUESTION 4 The column in Fig. 4 is constructed from high-strength concrete and six steel reinforcing rods. If it is subjected to an axial force of 150 kN, determine the average normal stress in the concrete and in each rod. Each rod has a diameter of 23 mm. Est = 215 GPa, Ec = 30 GPa. 100 mm- 150 kN 1.2 m

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

Two columns A and B are situated 6 m apart. Colum A transfers a load of 500 kN and column B, a load of 250 kN. Determine the resultant vertical stress on a horizontal plane 20 m below the ground surface below point A. a.12.4 kPa b.232.49 kPa c.29.9 kPa d.59.8 kPa
Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
A vertical 4.80-kN load is applied as shown on a wooden post of rectangular cross section, 80 by 120 mm (Fig. 11.40a). (a) Determine the stress at points A, B, C, and D. (b) Locate the neutral axis of the cross section.
Determine the normal stress in each of the cables? (MPa) a. 85.7 b. 75.7 c. 65.7 d. 55.7 If the cables elongated by 1 mm, what is the vertical displacement of the precasat slab? (mm) a. 1.758 b. 1.658 c. 1.458 d. 1.558 What is the tensile force in each of the cables? (kN) a. 5.98 b. 4.98 c. 7.98 d. 6.98 SOLVE ALL AND WILL GET A LIKE <3 ps: unit weight of concrete is 24kn/m^3
A short post constructed from a hollow circular tube of aluminum supports a compressive load of 250 kN (see figure). The inner and outer diameters of the tube are d1 = 9cm and d2 = 13cm, respectively, and its length is 100 cm. The shortening of the post due to the load is measured as 0.5 mm. Determine the compressive stress. (Disregard the weight of the post itself, and assume that the post does not buckle under the load).
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. the fc' is 28MPa, fy is 420MPa and Wu is 89.9kN/m. 1. what is the ultimate moment capacity of the beam? 2. what is the height of the equivalent stress block? 3. Determine the number of bars required for this beam
knowing that P = 18 Kips, determine the maximum stress when r = 0.45 in and r = 0.70 in
As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of thewhole structure which is SN lbs per ft complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94
The building slab is subjected to four parallel column loadings. The resultant force acts through point (12 m, 10 m). Suppose that F3 = 15 kN and F4 = 7 kN . a) Determine the magnitude of F1. b) Determine the magnitude of F2. Image is also provided.
A steel column of hollow circular cross section shown in Figure 2 is supported on a circular steel base plate and a concrete pedestal The column has outside diameter 220 mm and a wall thickness of 15 mm. It supports an axial load of 680 kN. a. Determine the bearing stress induced by the column to the base plate in MPa. b. If the allowable bearing stress on the pedestal is 10MPa, determine the required diameter of the base plate in mm.
A planned flexible load area (see Figure P7.2) is to be 3 m x 4.6 m and carries a uniformly distributed load of 180 kN/m2. Estimate the elastic settlement below the center of the loaded area. Assume that Df = 2 m and H = ∞ . Use Eqn 7.4
g. What is the moment of inertia (I) about the neutral axis of the section? (in mm^4) h. What is the first moment of an area (Q) about the neutral axis of the section? (in mm^3) i. What is the maximum shearing stress (fv) of the beam? (in MPa) j. What is the maximum flexural stress (fb) of the beam? (in MPa)