QUESTION 6 Figure 3 shows a conducting bar PQ that can slide freely over two conducting rails. The length of the bar is 75 cm. Calculate the induced voltage in the bar 50 cm Figure 3 a) att 10 ms when the bar is stationed at y = 30 cm and B = 4t2 az T. b) if the bar slides at a velocity u = 2 ay m s' and B = 4 az T.

QUESTION 6 Figure 3 shows a conducting bar PQ that can slide freely over two conducting rails. The length of the bar is 75 cm. Calculate the induced voltage in the bar 50 cm Figure 3 a) att 10 ms when the bar is stationed at y = 30 cm and B = 4t2 az T. b) if the bar slides at a velocity u = 2 ay m s' and B = 4 az T.

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter14: Inductance

Section: Chapter Questions

Problem 9CQ: How does the self- inductance per unit length near the center of a solenoid (away from the ends)...

See similar textbooks

Similar questions

, (a) At what angle 0 is tlie torque on a current loop 90.0% of maximum? (b) 50.0% of maximum? (c) 10.0% of maximum?
Check Your Understanding What Is the magnitude of the induced electric field in Example 13.8 at t=0 if r= 6.0cm, R= 2.0cm,n = 2000 turnspermeter, I0= 2.0A, and a = 200s-1?
Check Your UnderstAnding Verify the directions of the induced cuffents in Figure Figure 133 (a)Qosig the switch of ciicuit 1 produces ashort4ived cuicenz surge in circuit2 (b) If the switch remains closed, no current is observed in cituit 1 (c) Opening the switch again produces a short-lived cuirent in circuit 2 but in the opposite direclion fiom before.
How does the self- inductance per unit length near the center of a solenoid (away from the ends) compare with its value near the end of the solenoid?
Hall potentials are much larger for poor conductors than for good conductors. Why?
Is the magnetic field inside a toroid completely uniform? Almost uniform?
Design a current loop that, when rotated in a uniform magnetic field of strength 0.10 T, will produce an emf =0 sin t. where 0=110V and 0=110V .
A wire of length 1.0 m is wound into a single-turn planar loop. The loop carries a current of 5.0 A, and it is placed in a uniform magnetic field of strength 0.25 T. (a) What is the maximum torque that the loop will experience if it is square? (b) If it is circular? (c) At what angle relative to B would die normal to the circular coil have to be oriented so that the torque on it would be the same as the maximum torque on the square coil?
A solenoid with 4 x 107turns/m has an iron core placed in it whose magnetic susceptibility is 4.0 x 103. (a) If a cent of 2.0 A flows through the solenoid, what is the magnetic field in the iron core? (b) What is the effective surface current formed by the aligned atomic current loops in the iron core? (c) What is the self-inductance of the filled solenoid?
A bar magnet falls under the influence of gravity along the axis of a long copper tube. If air resistance is negligible, will there be a force to oppose the descent of the magnet? If so, will the magnet reach a terminal velocity?
Show that the expression for the magnetic field of a toroid reduces to tlrat for the field of an infinite solenoid in the limit that the cenmal radius goes to infinity.
Suppose you wish to produce 1.2-T magnetic field in a toroid with an iron core for which =4.0103 . The toroid has a mean radius of 15 cm and is wound with 500 turns. What current is required?