QUESTION 8 Select all correct answer(s). A 50 MVA RE generator is generating 40 MW active power. Which statement is core The RE generator can generate a reactive power of 10 MVar. The RE generator can generate/consume zero reactive power. | The RE generator can consume maximum reactive power of 30 MVar. O The RE generator can generate a minimum reactive power of 10 MVar. O The RE generator can consume a minimum reactive power of 20 MVar. O The RE generator can generate maximum reactive power of 10 MVar.

QUESTION 8 Select all correct answer(s). A 50 MVA RE generator is generating 40 MW active power. Which statement is core The RE generator can generate a reactive power of 10 MVar. The RE generator can generate/consume zero reactive power. | The RE generator can consume maximum reactive power of 30 MVar. O The RE generator can generate a minimum reactive power of 10 MVar. O The RE generator can consume a minimum reactive power of 20 MVar. O The RE generator can generate maximum reactive power of 10 MVar.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.9P

See similar textbooks

Similar questions

A 3 phase, 60 Hz infinite bus bar is connected to two synchronous generators. Generator 1 has 12 poles and generator 2 is running at 240 rpm. Determine the speed of generator 1 and number of poles of generator 2.
c) On 24th May 2021, there was a fault that caused wide power outage in Ghana from 7pmto 1am, the whole country was in total darkness. When the Volta River Authority (VRA) was contacted, they explained that the generators experienced massive system transient stability. In your own understanding of Synchronous generator, what would you recommend VRA do to restore power and bring the country back to light anytime there is such occurrence?
A generator is rated 100 MVA, 22 kV. Its Y connected windings have areactance of 1.1 per unit. Find the reactance of the winding. Then find a new per unit value of reactance of the generator for 100 MVA and 20 kV.
q19/ choose the correct answer ..........................capacitors will supply reactive VAR during peak load condition and consumes reactive VARs during light load conditions 1- Booster Transformers 2- Shunt 3- Synchronous 4- Series
A generator is rated 100 MVA, 15 kV. It is Y-connected, solid grounded and is operated at rated voltage at no-load and is disconnected from the rest of the system. Its positive and negative sequence reactances are 0.10 p.. and its zero sequence reactance is 0.05 p.. Calculate in ohms of inductive reactance to be inserted in the neutral connection of the generator to limit the fault current for a single line to ground fault to the fault current of a symmetrical three-phase fault.
A 100-MVA, 18-kV generator is connected to a transformer. The generator has reactances of 19%, 26% and 130% and time constraints of Td" = 0.035 sec, Td' = 2.0 sec and TA = 0.2 sec. It is operating at no load and rated voltage when a three-phase short circuit occurs at the generator terminals. Calculate:a. The initial symmetrical rms fault current in kA b. The sustained rms fault current in kA
a) draw the reactance diagram based on values in A busbar. U=29 S=30 b) while the voltage in B busbar is 13kV, 17MW 0.85 inductive power factor in M1, 8MW 0.9 inductive power factor in M2, what should be the terminal voltage in generator? c) to have a 3 phase fault in B busbar, what should be the fault current?
Figure 2 shows the circuit of a simple power system. The ratings of the generators, transformers and the motors are as shown in the figure. The reactance of lines 1 and 2 are 40 ohms and 50 ohms respectively. Assume that system is unloaded, and the generators are generating their rated voltage. Select the generator G₁ ratings as base values. Choose the fault location in bus 1 And give the below answers For a symmetrical three phase fault on the bus (a).Determine the Thevenin's equivalent circuit which can be used to calculate the fault current. (b) Calculate the fault current contribution from the generator connected to the bus on which you have selected for fault calculation
5. Two 75 MVA 3-phase alternator are connected in parallel. The speed load characteristic of the first generator is 2% from no-load to full load while that of the second alternator is 3% from no-load to full load. The machines are fully loaded when the load is 150 MVA. If the load is reduced to 80 MVA. Calculate the load carried by each machines?
Q5: A SL-G fault occurs on the low voltage side of a transformer that connects a motor to a generator at generating plant. The rated values for each element are:M: 0.6 kV, 5 MVA, X1 = X2 = 20%, X0 = 4%, grounded through 2% reactance.T: 3-single phase units, each is: (2400 Grounded Y: 600 Δ) V, 2.5 MVA, Xt = 10%.G: 4.16 kV, 7.5 MVA, X1 = X2 = 10%, X0 = 5%, grounded through 5% reactance.Draw the sequences networks and determine the fault current in Amperes. (Take the generator ratings as a base).
Figure 2 shows the circuit of a simple power system. The ratings of the generators, transformers and the motors are as shown in the figure. The reactance of lines 1 and 2 are 40 ohms and 50 ohms respectively. Assume that system is unloaded, and the generators are generating their rated voltage. Select the generator G₁ ratings as base values. Choose the fault location in bus 3. And give the bellow answer For a symmetrical three phase fault on the bus 3 1. Calculate the fault current in ampere and fault power in MVA and the fault current contribution from the generator connected to the bus 3.
True or false 1. Three phase fault is the most commonly occurring fault than other types of faults. 2. The range of generator rotor angle for stable operation is 0°< s < 180°. 3. The infinite bus in power system is a large system with infinite voltage. 4. At value of (s= 90°) the maximum power transfer takes place. 5. Per unit system (PU) is a ratio of actual value in any units to the base or reference value in the same units.