Continuous 1.502e+04 powergui Ps 1.817e+04 zl=0.5+0.7j Transmission ines Load 1 C1=? Load 2 V=415V f=50HZ ZL1=(10+j5) ohm C2=? ZL2=(2+7j-4j) ohm Figure 2: power factor correction a) Calculate the value of C1 and C2 for obtain unit power factor for each load C1=..... .C2=....... b) Complete the previous model 1 by connecting capacitors in parallel with loads (as shown in figure 2) c) Run the model 2 (must include display of pf1, pf2 and pfs) and show a print screen of results d) Write the obtained results Pfs=

Continuous 1.502e+04 powergui Ps 1.817e+04 zl=0.5+0.7j Transmission ines Load 1 C1=? Load 2 V=415V f=50HZ ZL1=(10+j5) ohm C2=? ZL2=(2+7j-4j) ohm Figure 2: power factor correction a) Calculate the value of C1 and C2 for obtain unit power factor for each load C1=..... .C2=....... b) Complete the previous model 1 by connecting capacitors in parallel with loads (as shown in figure 2) c) Run the model 2 (must include display of pf1, pf2 and pfs) and show a print screen of results d) Write the obtained results Pfs=

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
Does Ohm’s Law appear to hold in this exercise? How?
The problem is shown in the image below, v1 = 20 angle 15° volts, V2 = 10 angle -30° volts, V3 = -5 angle of 10° volts, and other components are shown in the image (units in Ω). When R3 is the load, calculate the replacement voltage (VTh), and the replacement current (IN)
Wiat is the difference between a real independent voltage source and an ideal independent voltage source? Give an example of a real voltage source and explain how it differs from the ideal.
What is meant by FACTS in power systems? Discuss about STATCOM type FACTS device.
Combination circuit what is PT? RT? IT? Voltage Across each load?
Electrical Engineering _ Energy Conversion Systems pls findthe question by using computer line. pls find fast.
A DC line has a resistance of 0.8 ohms. A load of 10 KW is taken at far end, while at the midpoint a current at 14 ampere at 204 volt is taken.Please find the supply voltage.
How do I solve this using Kirchoff's Voltage Law?
Write about dc power supply Function Uses field How it used How it work Advantages and disadvantages Refer to parts names Pls no plagiarism
Describe how electrical engineering and electrical engineering technology differ and are the same with regard to adaptability to current industrial practices
AA chopper circuit in the figure, 400 ? (???)Control the power of an ohmic load from a 50 ?? source.. Since the load resistance is 20 Ω and ? = 30 °,a) The effective voltage, current and power of the load,b) Input power factor,c) Apparent, active and reactive powers drawn from the network,d) Minimum blocking voltage of thyristor,e) Average value of each thyristor current,f) The required firing angle for the power transferred to the load to be 80% of the maximum power,calculate.