Problem 1. Due to cost and right-of-way constraints, Rv is determined to be 890 ft. Superelevation is 12%. What is the design speed? (As you have recalled from class, design speed is the highest speed at which one can drive under desirable weather conditions. Design speed is expressed in an increment of 5 mph.)

Problem 1. Due to cost and right-of-way constraints, Rv is determined to be 890 ft. Superelevation is 12%. What is the design speed? (As you have recalled from class, design speed is the highest speed at which one can drive under desirable weather conditions. Design speed is expressed in an increment of 5 mph.)

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter6: Fundamental Principles Of Traffic Flow

Section: Chapter Questions

Problem 4P

See similar textbooks

Similar questions

Determine the practical stopping distance (ft) for a road with speed limit of 45mph and grade of -3.8% Round your answer to 3 decimal places.
In a 500 m section of highway, there are 10 vehicles observed. The time headway is 4 sec. Determine the space mean speed of the vehicles in kph.
28.If the coefficient of friction between vehicles and the roadway is 0.4 and the radius ofthe curvature of the road is 30 meters, what is the maximum speed allowable if there isno banking?
The distance traveled by the vehicle in the opposite direction is 100 m on two lane two lane roadway. If the acceleration of overtaking vehicle is 3 km/h/sec and time of initial manoeuver is 4 sec. thus the safe overtaking vehicle speed rounded to integer number is ..........km/h
1. A Honda Civic is driven at 15 kph for 12 min, then at 40 kph for 20 min, and finally at 50 kph for 8 min. a. Calculate the average speed over the interval. (in kph) b. How fast must the honda civic move in the Last a min of travel to obtein an average speed of 55 kph? (in kph) Show FBD and complete and detailed solution.
Determine the practical stopping distance (m) for a road with speed limit of 50kph and grade of 4.9%.
A driver (with a reaction time 0.60 sec) is driving down hill on a 5% grade at 60 km /hr .find minimum stopping sight distance required on highway section ?assume coefficient of friction =0.7 locked wheels?
A section of highway has a speed–flow relationship of the form q = au2 + bu, where q is the traffic flow in veh/h, u is the space-mean speed of traffic in mi/h, and a and b are unknown parameters. It is known that at capacity (which is 3100 veh/h) the spacemean speed of traffic is 28 mi/h. Determine the speed when the flow is 1500 veh/h and the free-flow speed.
Assume you are observing traffic in a single lane of McArthur Highway at a specific location. You measure the average headway and average spacing of the vehicles as 3.2sec. and 50 m. respectively. Determine the traffic speed in kilometer/hour
While traveling at a constant speed a driver saw a road block 112 m away. He applied the brakes and the car decelerated uniformly at 6.4 m/s2. It stopped 5 m from the block. The driver’s PRT is 2.2 seconds. Sketch and calculate the initial constant speed of the vehicle in kph if;a. The roadway is levelb. The roadway grade is +10%c. The roadway grade is -10%
You are designing an on-ramp that connects an intersection (controlled by a signal) and the highway. You want to assure that vehicles that are completely stopped at the intersection can reach the prevalent highway speed, which is assumed to be 60mph. Assume that passengers have the maximum acceleration rate of 10 ft/sec2 , trucks have smaller acceleration rate 3.2 ft/sec2 . You can assume that vehicles can use the maximum acceleration rate regardless of the speed. What’s the reasonable length for the ramp?
The average center to center spacing of vehicles in a simple lane highway is 50 m. The volume of traffic is 600 vehicles per hour. Determine the average speed of the cars using this lane.. help