Question NO: 1Consider the network as shown in figure Q1. Determine the load impedance ZL for maximum average powertransfer and the maximum average power transferred to the load.4020- j6 2502015 ΩZLj52Figure Q.1Question NO: 2Consider an induction load consumes 135kW at 0.85 pf lagging from a 24020°-V rms 50 Hz. A bank of capacitorstotaling 600 µF is available. If these capacitors are placed in parallel with the load what is the new power factor of

From Maximum Power Transfer Thereom

Question NO: 1 Consider the network as shown in figure Q1. Determine the load impedance ZL for maximum average power transfer and the maximum average power transferred to the load. 4020 - j6 2 5020 15 2 ZL j52 Figure Q.1 ww

Question NO: 1 Consider the network as shown in figure Q1. Determine the load impedance ZL for maximum average power transfer and the maximum average power transferred to the load. 4020 - j6 2 5020 15 2 ZL j52 Figure Q.1 ww

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Related questions

Q: Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The…

A: Given Vline=13.2kv⇒Vph=Vline3=13.23=7.62kv Apply kVL Vph=I Zline+Zload…

Q: For the following circuit, find (a) the load impedance required for maximum average power transfer…

Q: A 13.2-kV single-phase generator supplies power to a load through a transmission line shown in…

A: As per question asked , we are giving the solution of 8(a). When two impedence x and y connected in…

Q: Predict the wattmeter readings for the circuit in Fig. z 208/0° V W2 208/-60° V Z = 60 – j30 2 ll…

A: Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…

Q: AC Power and Power Factor 1. Two loads are connected in parallel across a 13,200-volt line. Load A…

Q: Problem 4: For the circuit shown in figure, compute the average power delivered to the load, the…

Q: A wye-connected load with ZA = 12 + j12 Q, ZB = 15 + j 20 Q and Zc = 10 Q is connected to a…

A: In this question, We need to determine the power factor of the given system? Power factor =…

Q: Q2: In the circuit shown in Figure 2 calculate a) load current and voltage b) average and reactive…

Q: 1. a) Find the average power dissipated in the line shown.2. b) Find the capacitive reactance that…

Q: isible power of Z1 = |S1| = 16 kVA and at 0.8 back power factor; Visible power of Z2 = |S2| = 25…

A: Given data: S1=16 kVApf1=0.8S2=25 kVApf2=1ZW=5+j26 ΩVL=3.8 kV

Q: Q3 (a) In Figure Q3(a), the load impedance, Zi is adjusted until it absorbs the maximum average…

Q: a transmission line has an impedance of 4 12 Ohms/phase, Find the per-unit impedance of this line on…

Q: 9. Two single-phase ideal voltage sources are connected by a line of impedance of 0.7 + j2.4 Q as…

Q: 150mH .. .. .. |L1. 150mH C1 V2 120Vrms 60HZ 0° =22µF .. R1 602

A: Given a circuit : We need to : a. Measure Vrms and Irms across ZLoad. Insert a capture of your…

Q: Assume that the phase-voltage magnitudes for a wye system are 100V. Find the magnitude of the…

Q: 3. Suppose a voltage v(t) = v2 x 120 sin(377t + 30°) is applied to a single phase load, and the…

Q: Q. 2a) The impedance Zi and Z2 are connected in parallel across 200 V, 50 HZ single phase ac supply.…

Q: For the network shown in the figure below: a. Find the total impedance Zt. b. Calculate the voltage…

A: Series Connection of Impedances: When n no. of impedances is connected in series, their equivalent…

Q: A 15-ŁV single-phase generator is used power to a load (ZLesd = 400+j300 Q) through a transmission…

A: Wewill find the total impedance seen from the source then we will find current(I)in the line. Using…

Q: The voltage and current of a load are given by the equations: V = 120sin(wt + 30)v and I = sin(wt…

Q: 22 32 552 reele 10 20° 1460 32 (b) Determine the Real power, Reactive power consumed by the marked…

A: In this question, We need to find the real and reactive power in the RX branch. S= VI*

Q: Consider the circuit shown in Figure 3. (i) Find the total impedance ZT as seen by the voltage…

Q: Example-15.7 A balanced delta connected load has an impedance of 9430° 2 per phase. What is the…

A: we need to find out impedance in star configuration.

Q: An alternator is connected in star. Its phase voltage is 250 V. This alternator supplies the load…

A: We have an alternator that is connected in star and gives supply to an delta connected load with,…

Q: 1. A wye-connected load with ZA= 12 /45, ZB= 15 / 30 and Zc= 10 /0 is connected to a four-wire, 208…

Q: 4Ω ww- ell Determine the load impedance that z, maximizes the average power drawn from the circuit.…

A: For dc source the maximum power transfer states that maximum power is abstract by load resistance if…

Q: 12 2 V V 310

Q: Design the series circuit needed to meet the voltage and current requirements as shown. Provide the…

A: a)

Q: 9. A three-phase overhead transm potentials across the first and se (i) the line voltage (ii) the…

Q: ww 5/30° V

Q: Find the total real power dissipation in a balanced delta-connected system. Phase voltage is 100V…

A: Given: A balanced delta connected system Phase voltage, Vph=100 V Load impedance, Zph=175 Ω Power…

Q: Find: The real, reactive and apparent power at the load Power factor at the source and load side Z,…

A: impedance, Z = ZR + ZC Z = 400 - j300 magnitude of (Z) = 4002+3002 = 500…

Q: A 50 2 transmission line is matched with a load Z1. If the frequency of operation is 100MHZ and the…

A: Here they have mentioned the transmission line with characteristic impedance ZO = 50 Ohm. Given…

Q: For the given circuit calculate the maximum power that can be transferred from the circuit to the…

A: In the given circuit, Find the maximum power transfer to the load impedance ZL For maximum power…

Q: QUA power plant has to meet the following load demand: Load A: 100 MW from 8 AM - 6 PM Load B: 150…

Q: consider the following diagram of impedances in per unit of a common base a) get the YBus admittance…

Q: 5 Assume a Thévenin equivalent source composed of V, in series with Ze (a) Prove that maximum…

Q: Two circuits, the impedances which are given by z₁ = 15+j12 and z₂ = 8 - j5 ohms are connected in…

Q: Figure below shows a simple single-phase AC power system with three loads. The voltage source is V =…

A: Kirchoff's voltage law is an important method to solve big and complex circuits. According to KCL,…

Q: Find the current in z₁ and 22 respectively when they are connected in parallel and supplied by 230…

A: We have an circuit with, Z1 = 3 + j 4 Ω Z2 = 3 - j 4 Ω Voltage Supplied (V) = 230 V = 230 ∠0° And…

Q: Consider the network as shown in figure Q1. Determine the load impedance ZL for maximum average…

A: We will use thevenine theorem to find load impedance and maximum power transfer to load.

Q: j2 Ω m -jXcQ HE RQ ww 40/0° V ZL 5Ω or the circuit shown above, what is the magnitude of the load…

Q: A balanced three-phase with phase voltage of 4200-Vrms and the transmission line has an impedance of…

A: In this question we need to find a loss in transmission line for the given load condition

Q: 1. A series AC circuit consisting of R = 200 2 and L = 320 mH are connected across V = 20 VL0°, 100…

A: 1) For a series AC circuit consisting of R and L Determine the following : Inductive reactance,…

Q: Q3 (а) Given a circuit in Figure Q3(a); Determine the load impedance, Zı that results in maximum…

A: Maximum power transfer to ZL when Load impedance is equal to complex conjugate of thevinin…

Q: A single phase circuit is supplying the two loads, Load1 draws a real power of 350 kW at a unity…

A: Solution: For load 1: P=350 kWCosϕ=1Apparant power:S=PCosϕ=3501S=350 kVA

Q: Three impedances Za = 4 - j3 ohms, Zc = 4 + j4 ohms and Zr = 3+johms are connected in parallel.…

Q: □6 Assume a Thévenin equivalent source composed of V, in series with Zeq = Ree+1X (a) Prove that…

Q: 13 10+is 25 For the circuit shown below, Take Van = 100 Vrms and the transmission line impedance is…

A: In this question, choose the correct option What is the real power in the phase B.

Q: For the network shown below find: a) Zr. I. V, the power factor and the total average power…

A: Power factor: It tells how much active power is utilized by the circuit from apparent power.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Single Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Under balanced operating conditions, consider the three-phase complex power delivered by the three-phase source to the three-phase load. Match the following expressions, those on the left to those on the right. (i) Realpower, P3 (a) (3VLLIL)VA (ii) Reactive power, Q3 (b) (3VLLILsin)var (iii) Total apparent power, S3 (c) (3VLLILcos)W (iv) Complex power, S3 (d) P3+jQ3 Note that VLL is the rms line-to-line voltage, IL is the rms line current, and is the power-factor angle.
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.
An industrial plant consisting primarily of induction motor loads absorbs 500 kW at 0.6 power factor lagging. (a) Compute the required kVA rating of a shunt capacitor to improve the power factor to 0.9 lagging. (b) Calculate the resulting power factor if a synchronous motor rated at 500 hp with 90 efficiency operating at rated load and at unity power factor is added to the plant instead of the capacitor. Assume constant voltage (1hp=0.746kW).
Between the terminals a and b in the figure, there is a load formed by connecting the resistor R0 and inductance L0 in series. The amplitude of the voltage Vs (t) is √2 150 volt phase angle Qs = 0 degree period T = 200π microseconds. Since R = 300ohm and C = 1 microfarad A) If the load phase angle QL = 30 degrees, find the values of R0 and L0 that enable the load to draw the maximum average power from the circuit. =? B) Calculate the average power on the load. =?
The 9 Ω resistor in the circuit is replaced with a variable impedance Zo. Assume Zo is adjusted for maximum average power transfer to Zo. 1. a) What is the maximum average power that can be delivered toZo?2. b) What is the average power developed by the ideal voltage sourcewhen maximum average power is delivered to Zo?3. c) Choose single components from Appendix H to form animpedance that dissipates average power closest to the value in part(a). Assume the source frequency is 60 Hz.
1. A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume 120Vac, 60 Hz supply. a. What is the complex impedance of the load? b. What is the ac current through this load? c. What is theta, the angle between voltage and current through this load? d. What is the power factor? e. What capacitance should be added in parallel with this load to correct the power factor to 1? f. What is the current from the supply when the power factor is corrected?
The variable resistor Ro in the circuit shown is adjusted until maximum average power is delivered to Ro.1. a) What is the value of Ro in ohms?2. b) Calculate the average power delivered to Ro.3. c) If Ro is replaced with a variable impedance Zo, what is themaximum average power that can be delivered to Zo?4. d) In (c), what percentage of the circuit’s developed power isdelivered to the load Zo?
There is a load formed by the series connection of the resistor R0 and the inductance L0 between the terminals a and b in the figure. The amplitude of the voltage Vs (t) is √2 150 volts, phase angle θs = 0 ° degrees, period T = 200π microseconds Since R = 300 Ω and C = 1µF a) If L0 = 0 H is constant, find the value of R0 that allows the load to draw the maximum average power from the circuit. b) calculate the average power on the load
In the circuit in the figure, there is a load consisting of the series connection of the resistor R0 and the inductance L0 between the terminals a and b. The amplitude of the VS (t) voltage is √2 150 volts, phase angle = 0 degrees, period T = 200π microseconds.Since R = 300 ohms and C = 1 microfarad a)Find the values of R0 and L0 that enable the load to draw maximum average power from the circuit when the load phase angle is constant at 45 degrees? b)Calculate the average power on the load?
From the circuit given below, How can I find the value of load Z for the maximum power transfer and the maximum average power transferred?
1. Solve for the equivalent impedance and admittance seen at the source. Solve for is(t). 2. A load Z draws 12 kVA at a power factor of 0.856 lagging from a 120-Vrms sinusoidal source. Calculate: (a) the average and reactive powers delivered to the load, and (b) the peak current.