Question2-1 Thermal hot wire anemometers measure the temperature of the flow, and they are very small devices which do not disturb the flow significantly. Question2-2 Using a Laser Doppler velocimetry, one can measure the velocity information at a cross section instantaneously. Question2-3 An obstruction flow meter can be used to measure the velocity profile around a car in a wind tunnel. Question2-4 The exact value of the discharge parameter of an orifice meter should be supplied by the producer because it has a design based value.

Question2-1 Thermal hot wire anemometers measure the temperature of the flow, and they are very small devices which do not disturb the flow significantly. Question2-2 Using a Laser Doppler velocimetry, one can measure the velocity information at a cross section instantaneously. Question2-3 An obstruction flow meter can be used to measure the velocity profile around a car in a wind tunnel. Question2-4 The exact value of the discharge parameter of an orifice meter should be supplied by the producer because it has a design based value.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.46P

See similar textbooks

Similar questions

Air flows at 700 m/sm/s through a long duct in a wind tunnel, where the temperature is 15∘C∘C and the absolute pressure is 95 kPakPa . The leading edge of a wing in the tunnel is represented by the 8∘∘ wedge. The angle of attack is set at α� = 1.5∘∘. (Figure 1) Determine the pressure created on its top surface. Express your answer to three significant figures and include the appropriate units.
Liquid A(sp gr = 0.95) at a temperature of 29°C is flowing at a rate of 120gal/min in a pipe with an inside diameter of 2.343 in. If the reynold number is 5.6 x 10^5. what is the viscosity of liquid A in centipoise. Final answer in four decimal.
At one point in a pipeline the water's speed is 3.00 m/sand the gauge pressure is 5.00×10^4 Pa a) Find the gauge pressure at a second point in the line, 11.0 mm lower than the first, if the pipe diameter at the second point is twice that at the first. Express your answer in kilopascals.
A fluid is flowing in a glass pipe at a rate of 0.587 kg/s. The pipe has a diameter of 67.5 mm. If the fluid has a density of 1030 kg/m^3 and a viscosity of 2.12 cP at 20 degrees Celsius, determine the Reynolds number. Report your answers to the nearest whole number. Do not round off intermediate answers.
For a gas, which of the following does not vary with temperature? - the gas soecific weight - the gas dynamic viscosity - the gas specific volume - the gas constant R - the gas density
The altimeter of a C-152 reads 8,200 ft. The reading from its pitot tube is 574.452003 millimeters of Mercury. If the outside air temperature is hotter than the standard sea level temperature by 25°F, determine the true airspeed of the aircraft in fps. Assume incompressible flow. Round off the answer to 2 decimal places.
(1) A simple, vertical U-tube manometer is used to measure the differencebetween two gas pressures.Write down an equation for the pressure difference in terms of the difference inthe level of the fluid in the manometer. Describe briefly, with the help ofdiagrams, two modifications to the basic design which offer greater sensitivity tosmall pressure differences. Give equations for their use. ii) An extractor fan draws air from a room and delivers it to the surroundingsthrough a 5m long circular duct of diameter 0.1m. The friction coefficientfor the duct flow is 0.002. The fan characteristic, relating its total pressurerise, ∆P (Nm-2) to the volume flow rate is: ∆P = 103−7x104Q 2. What is therate of flow through the duct?You may assume that the room and surroundings are both at atmosphericpressure; state and justify any other assumptions you make.
An air bubble is observed from the bottom up to the water surface The atmospheric pressure is 101 325 kPa The volume of the bubble at the bottom is 1/7 times the volume of the bubble at the surface Determine the height of the water in meters.
The height of the fluid inside the tube after immersion is 1⁄8 the height of the cylinder glass tubing. It was immersed into a tank of a cleaning solvent with specific gravity of 0.83. The remaining length of tube above the surface is 6 cm. Determine the length of the tubing with an inside diameter of 4cm. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m
a. What is the type of the two liquids?b. Explain how the shear force applied to each liquid affects its viscosity.c. Which liquid has higher apparent viscosity? Explain your answer.
In medical work, pressures are often measured in units of mm of H2O because body fluids, including the cerebrospinal fluid, typically have nearly the same density as water. The pressure of the cerebrospinal fluid can be measured by means of a spinal tap. A hollow tube is inserted into the spinal column, and the height to which the fluid rises is observed. If the fluid rises to a height of 160 mm, we write its gauge pressure as 160 mm H2O. a) Sometimes it is necessary to determine whether an accident victim has suffered a crushed vertebra that is blocking the flow of cerebrospinal fluid in the spinal column. In other cases, a physician may suspect that a tumor or other growth is locking the spinal column and inhibiting the flow of cerebrospinal fluid. Such conditions can be investigated by means of the Queckensted test. In this procedure the veins in the patient’s neck are compressed, to make the blood pressure rise in the brain. The increase in pressure in the blood vessels is…
The human brain and spinal cord are immersed in the cerebrospinal fluid. The fluid is normally continuous between the cranial and spinal cavities and exerts a pressure of 100 to 200 mm of H2O above the prevailing atmospheric pressure. In medical work, pressures are often measured in units of mm of H2O because body fluids, including the cerebrospinal fluid, typically have nearly the same density as water. The pressure of the cerebrospinal fluid can be measured by means of a spinal tap. A hollow tube is inserted into the spinal column, and the height to which the fluid rises is observed, as shown in the figure below. If the fluid rises to a height of 150 mm, we write its gauge pressure as 150 mm H2O. A patient lies sideways while a surgeon tries to insert a hollow tube into his spinal cord. (a) Express this pressure in pascals, in atmospheres, and in millimeters of mercury. (The density of water is 1.00 ✕ 103 kg/m3, and the density of mercury is 13.6 ✕ 103 kg/m3.) pascals kPa…