Atmospheric air at 40°C dbt and 55% RH is passed over a cooling coil at the rate of600 m'/mint. At exit from coil the air is saturated and its temperature is 8°C. Thecondensate also leaves at 8°C. Determine the amount of condensate leaving coil perminute and refrigeration in kW, The specific heat of superheated steam may beassumed to be 1.88 kJ/kg-K. Solve the problem without psychromatic chart.

Answered: rat 40°C dbt and 55% RH is passed over…

rat 40°C dbt and 55% RH is passed over a t exit from coil the air is saturated and itst leaves at 8°C. Determine the amount of cor rigeration in kW, The specific heat of sup

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The air conditions at the intake of an air compressor are 28oC DB, 50% RH, and 101.325 kPa. The air is compressed to 400 kPa, then sent to an intercooler. If condensation of water vapour from the compressed air is to be prevented, what is the minimum temperature to which the air can be cooled in the intercoolers?
Atmospheric air at 40°C dbt and 55% RH is passed over a cooling coll at the rate of 600 m/mint. At exit from coil the air is saturated and its temperature is 8°C. The condensate also leaves at 8°C. Determine the amount of condensate leaving coll per minute and refrigeration in kW. The specific heat of superheated steam may be assumed to be 1.88 kJ/kg-K. Solve the problem without psychromatic chart.
An isobaric boiler vaporizes saturated liquid water at 200kPa until it is saturated vapor. If the mass flowrate of the water is increased but the same heat transfer rate is maintained, what should be the new state of the boiler outlet? a. Subcooled liquid b. Superheated vapor c. Mixture of liquid and vapor d. Saturated vapor
In a certain geothermal area, studies show that 1,500,500 kg/hr of pressurized ground water is available at 2500 psia and 6200F. The water will be throttled to 250 psia to produce ert steam and this mixture will be passed through a water separator to remove the water droplets so that saturated steam at 250 psia is available at the entrance of steam turbine for the proposed power plant. Other data are as follows: Discharge pressure of turbine 25 in. Hg. Vaccum Turbine Engine efficiency 75% Mechanical Loss1.5% of shaft power Generator efficiency 97% Assume atmospheric pressure to be 30 in. Hg. Determine the maximum amount of power in kW that the plant can generate.
Steam is delivered to turbine at 5.4 MPa and 600 degree C. Before condensation at 31 degree C, steam is extracted for feed water heating at 0.6 MPa. The turbine exhaust is 60 degree C. the required values of some state point properties are tabulated below. 6. Determine the enthalpy of bled steam entering the open feed water heater.
R-134a in saturated liquid form at -16 degree in an ice machine is evaporated to atmosphericpressure and ensured to freeze at 0 degree. R-134a is leaving from the evaporator as saturated vaporis known. The device produces ice at a flow rate of 2000 kg / h and a temperature of 0 degree. Calculate the entropy generation rate.
PROBLEM: A flashed-steam geothermal power plant is located where underground hot water is available as saturated liquid at 715 kPa, The well head pressure is 680 kPa. The flashed steam enters a turbine at 635 kPa and expands to 15 kPa, when it is condensed. The flow rate from the well is 35.3 kg/s. Determine: Draw the T-S diagram The mass flow rate of steam in kg/s The power produce in KW The cooling water flow in kg/s if water is available at 25 oC and a 15°C rise is allowed through the condenser.
I need help on the following question: The vapour compression cycle (picture provided), utilises the refrigerant R134a flowing at 0.05 kg s-1. Assuming that the compression is adiabatic and reversible. If the actual input power to the compressor is 2 kW, then: 1. You need to determine the theoretical input power to the compressor and the heat transfer (Φ) to theevaporator. Take the enthalpies h1, h2, and h3 to be 238.41, 263.68 and 81.5 kJ kg-1 (use the 'NH3 Refrigeration Table' where you can find online). 2. You need to determine the coefficient of performance based on your answer to the previous question (1). 3. You need to determine the compressors mechanical efficiency.
Steam is delivered to turbine at 5.4 MPa and 600 degree C. Before condensation at 31 degree C, steam is extracted for feed water heating at 0.6 MPa. The turbine exhaust is 60 degree C. the required values of some state point properties are tabulated below. 7. Determine the quality of steam at the condenser inlet.
200 m3/min is passed through the adiabatic humidifier. The condition of the air at inlet is 40C db and 15% RH and the outlet condition is 25C db and 20C wb. Find the amount of the water vapor added to the air per minute.
A flashed-steam geothermal power plant is located where underground hot water is available as saturated liquid at 725 kPa, The well head pressure is 670 kPa. The flashed steam enters a turbine at 645 kPa and expands to 15 kPa, when it is condensed. The flow rate from the well is 33.3 kg/s. Determine: Draw the T-S diagram The mass flow rate of steam in kg/s The power produce in KW The cooling water flow in kg/s if water is available at 25 oC and a 15°C rise is allowed through the condenser.
In a certain geothermal area it is shown that 1, 500, 000 kg/hours of pressurized ground water is available at 2500 psia and 620 deg F . The water will be throttled to a pressure of 250 psia to produce wet steam in this mixture will be passed through the water separator to removed the liquid droplets so that the saturated steam at 250 psia is available at the entrance o the steam turbine for the purpose of power plant . other plant data are as follows: Discharge pressure of the turbine = 25 inches vac.Turbine engine efficiency = 78%Mechanical loss 1.6 percent of mechanical powerGenerator efficiency = 97 % Assume the atmospheric pressure to be 30 inches Hg. Determine the maximum amount of power in kilogram -watt that the plan can be generate.