Read the problem carefully and provide complete solutions with derivation of formulas (integrals and derivatives). Complete solution and units please. Use two decimal plaas for final" answers only. min 5. A two- stage compressor receives air at 100 ft.³ at 10 psia and the discharge pressure is pressure is 200 psia. If the temperature of the air received is 50 F, find the intercooler pressure, total compresser work and total heat rejected at the intercoolers Answer: 44.72 psia, 16.31 hp, 345.80 Btu min

Read the problem carefully and provide complete solutions with derivation of formulas (integrals and derivatives). Complete solution and units please. Use two decimal plaas for final" answers only. min 5. A two- stage compressor receives air at 100 ft.³ at 10 psia and the discharge pressure is pressure is 200 psia. If the temperature of the air received is 50 F, find the intercooler pressure, total compresser work and total heat rejected at the intercoolers Answer: 44.72 psia, 16.31 hp, 345.80 Btu min

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A single acting two-stage air compressor deals with 4 m^3/min of air under atmospheric conditions of 1.013 bar and 15°C with aspced of 250r.p.m. The delivery pressure is 80 bar. Assuming complete inlercooling, find the minimum power required by the compressor and the bore and stroke of the compressor. Assume a pistonspeed of 3 m/s, mechanical efficiency of 75 percent, and volumetric efficiency of 80 percent per stage. Assumethe polytropic index of compression in both the stages to be it = 1.25 and neglect clearance.
The steam expands isentropically in a simple impulse turbine from 12 bar, 250°C with an enthalpy of 2035 k.J/kg to an enthalpy of 2584 ki/kg 2t 0.1 bar. The nozzle makes 20° with blade motion and the blades are symmetrical. Calculate the blade velocity that produces maximum efficiency for turbine speed of 3600 rom. Assume that the steam enters the nozzle with negiigible velocty.
Steam at 20 bar and 3000C is supplied to a turbine in a cycle and is bled at 4 bar. The bled-steam just comes out saturated. This steam heats water in an open heater to its saturation state. The rest of the steam in the turbine expands to a condenser pressure of 0.1 bar. Assuming the turbine efficiency to be the same before and after bleeding, find: a) the turbine efficiency and the steam quality at the exit of the last stage; b) the mass flow rate of bled steam 1kg of steam flow at the turbine inlet; c) power output / (kg/s) of steam flow; and d) overall cycle efficiency.
The steam rate to a turbine for variable output is controlled by a throttle valve in the inlet line.Steam is supplied to the throttle valve at 1,700 kPa and 225°C. During a test run, the pressure atthe turbine inlet is 1000 kPa, the exhaust steam at 10 kPa has a quality of 0.95, the steam flowrate is 0.5 kg/s, and the power output of the turbine is 180kW. 1. What are the heat losses from the turbine? 2. What would be the power output if the steam supplied to the throttle valve were expandedisentropically to the final pressure?
A single-acting, single-stage reciprocating compressor is required to deliver 55kg per hour from 750torr and 25 degree celcius conditions to 6750mm Hg delivery pressure of air . The compression is expected to follow PV1.15 = C, polytropic process. Determine the required work of compressor?
Steam is supplied to a two-stage turbine at 48 bar and 400 °C. It expands in the firstturbine until it is just dry saturated, then it is re-heated to 400 °C and expandedthroughthe second-stage turbine. The condenser pressure is 0.04 bar what is the pressure in bar at state 4 to 3 decimal places? what is the specific entropy in kJ/kg-K for state 5 to 4 d.p.?
The jet engine turbine receives air at 2150 °R, 230psi. It exhausts to a nozzle at 35 psi, which in turn exhausts to the atmosphere at 7.5 psi. Find the nozzle inlet temperature and the nozzle exit velocity. Assume air-standard analysis, internally reversible processes and negligible kinetic energy out of the turbine.
A twin cylinder, double acting, compressor with a clearance of 5% draws in oxygen at 450 kPa, 17 degree celsius and discharges it at 1800 kPa. The mass flow rate is 20 kg/min, compression and expansion are polytropic with n= 1.25 . Find (a) the work, (b) the heat transferred, and (c) the bore and stroke for 100 rpm and L/D = 1.20
There are compressed 11.33 m3/min of air from 103.42 kPa, 26.7°C to 827.36 kPa. All clearances are 8%. (a) Find the isentropic power and piston displacement required for a single stage compression. (b) Using the same data, find the minimum ideal power for two-stage compression when the intercooler cools the air to the initial temperature . (c) Find the displacement of each cylinder for the conditions of part (b). (d) How much heat is exchanged in the intercooler? (e) For a compressor efficiency of 78%, what driving motor output is required?
In a spray condenser, find the ratio of circulating water to steam flow if the condenser pressure is (0.07 bar), and the cooling tower cools the water to (18"C). Assume turbine exhaust at (89%) quality.
Water at 180 degrees Celsius (Psat = 1.0 MPa) and 13 MPa enters a boiler. It then leaves the boiler at 500 degrees Celsius. What is the mass flowrate of water?
In a nozzle, steam enters at T = 673.15 K and P = 800,000 Pa while u = 15m/s. It exits at T = 400,000 Pa and u = 320m/s. What is the ration of the inlet and outlet diameters (D1/D2)?