Refer to the diagrams to answer the following questions. 818 A B

Q: Clue 6 in. the

A: The given conditions are: The thickness of the wooden plank is 78 inch. Average shearing stress =…

Q: where did 144 come from

A:

Q: Write short notes on significance of grashoff number.

A: The answer is given below

Q: Mention the basic flame types a

A: Given: Basic Flame types

Q: In gas welding of a job, a neutral oxy-acetylene flame was used. If the acetylene consumption was 8…

A: Given, Type of flame = Neutral Acetylene consumption = CA = 8 litres   Let us take Oxygen…

Q: what is the length of the red line?

A: Solution:

Q: 10. Complete sketch A to show the significance of the welding symbol shown in sketch B.

A: This is a double J weld Configuration Problem which consist of different radius on both side.

Q: pot

A:

Q: = what will be the percentage

A: Given data; mass(m)=2kgharmonic exciting…

Q: Select the correct statement to represent the above problem (Answers are more than one).

A: (J) Correct explanation- The us = 0.3 is the coefficient of static friction that can be…

Q: Part A In Es 350N and10 Determine the magnitude of the resutant force Express your anser to three…

A:

Q: -is the change

A: Option (c) 300J is correct option

Q: elocity at a point inside

A: given:x=20cm

Q: pipe carries deion is capped (Figure ed to the end of t

A: given:pressure P=50psid=0.75int=0.5in

Q: 1*10 DeterMine f) from Modj char t?

A: Given :- Reynolds no. =72500 Relative pipe roughness= 0.001

Q: The discharge over a triangular no

A: Given data : Discharge =Q Acceleration due to gravity=g Head =h Coefficient of diacharge=Cd

Q: 10. Sketch the welding symbol that indicates the joint preparation and other elements required for…

A: Welding is fabrication process that joints meterials usually metals, thermoplastics by using high…

Q: Water enters the condenser at 20°C and leaves at 35°C. What is the log mean temperature difference…

A:

Q: ardne

A: introduction: Hardness is a material's resistance to localised plastic deformation. Hardness is only…

Q: A 著 染 D

A:

Q: value of h will be

A: Given: Figure shows a schematic diagram of simple watt governor mechanismwith spindle o1o2 rotating…

Q: possible methods. В A 4m 8m 4m 4m 600KN

A: To find magnitude of vertical and horizontal forces on each joint

Q: how to get the -y theo

A:

Q: Completely solve and box the final answer. Please show the units to show the unit cancellations.…

A:

Q: i need to know what each number means in the diagram.

A:

Q: The answers should not be in vector form. Please re-anser. Rate will be given

A:

Q: 0m and diameten

A:

Q: .1- Answer two of the following: a) What are deference between hot forming and cold fo

A: Hi and thanks for the question. Since you have asked multiple questions. As per the honour code, we…

Q: - where p' = Ap. %3D

A: Answer- Option a)

Q: 1) a) On a sketch illustrate natural gas fired power plant generating and delivering electricity to…

A: A gas-fired power plant or gas-fired power station or natural gas power plant is a thermal power…

Q: y 1 in. 3 in. -3 in.-

A: Area of the triangle, A1=1/2(3)6=9in2 Area of the square, A2=3(3)=9 in2 Area of the quarter circle,…

Q: n or equal to u*N

A: The value of dynamic friction is less than the static friction. So force required in dynamic…

Q: 17. Interpret the significance of the letters shown in the following illustrations (a through f). FW…

A:

Q: Which of the above mentioned values are correct for the value of n?

A:

Q: tan & = 8 - 缶 tan 3.

A:

Q: V a A В a

A: a=2.3inb=3.6ind=10.8int=0.4inV=39kips To-Find:- The shear flow through the welded surface at B

Q: A 4 stroke 4 cylinder car engine of 4 L. What will be the swept volume of each engine?

A: Given:A 4 stroke four cylinder  has a swept volume of 4litre(L)Since nothing else is mentioned we…

Q: a. Show how the extent of the surfacing weld is indicated between the vertical centerlines in the…

A: Writing the procedure to organise the weld between the lines on the flat. (1) Let us consider that…

Q: What is the elevation of liquid on end A? b. What is the elevation of liquid on end B? c. What is…

A: Solution: Given Data: Gage pressure: Pv=-17.1 kPa

Q: 3T tanux

A:

Q: With FBD and Solution pls refer to the second picture if the answer is in the choices one of those 5…

A: The free-body diagram of the junction of the boom, given load, and the force exerted by the cable,…

Q: B/ Choose correct answer from the following (choose 5 only): 1. The iron ore mostly used for the…

A: As per bartleby guidelines we are allowed to solve only 1st 3 questions if multiple subparts are…

Q: Question 21 and 22

A: 21 Explanation: In a gear train, the compound gears are the gears which are mounted on the same…

Q: flow. What is the pressure drop in the pipe "in Pascals"? Select one: A. 4.98

A: Fluid Mechanics: It is a branch of physics in which concerns with mechanics of fluids & forces…

Q: of the following causes increase in the diameter of a steam

A: Given Data : Increase in diameter of stem

Q: of the following OWI

A: Wood is composite type of (c) Polymer Matrix Composite (PMC) Polymer matrix composites are defined…

Q: 10

A: To find moment of inertia about x axis

Q: minimum value for the thickness of the plates

A: Given; What should be the minimum value for the thickness of the plates to guard against tensile…

Q: Solve Question 35.

A: In the given problem, we will draw free body diagram of each bar and then using equilibrium…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.