b) A prismatic bar with circular cross-section subjected to tensile force 85 kN. The barhas a length of 3.0 m and diameter 30 mm. It is made of aluminium with elasticmodulus 70 kN/mm? and Poisson's ratio 1/3. Distinguish elongation, & and diameterreduction, AD. Assuming stress at the limit of proportion is 180 kN/mm?.

Answered: Image /qna-images/answer/aebdb4ed-ca96-4686-a712-7b66a0e704ff.jpg

Answered: 0m and diameten

Engineering

Mechanical Engineering

0m and diameten

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8. A brass bar having cross-sectional area of 1000 mm? subjected to axial forces as shown below. Find the elongation of the bar if Young's Modulus of the material is 1.05 x 105 N/mm?
The cross sectional area of the bar is 5cm^2. Use E = 70GPa for aluminum, and E = 200 GPa for steel a. What is the elongation in segment AB (Aluminum)? b. What is the elongation in segment BC (Steel)? c. What is the elongation in segment CD (Aluminum)? d. What is the total elongation of the bar? -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
A 5.0m long steel wire has a cross-sectional area of 0.55cm^2. Its proportional limit has a value of 0.0018 times its Young's modulus. Its breaking stress has a value of 0.0065 times its Young's modulus. The wire is fastened at its upper end and hangs vertically. a. How great a weight can be hung from the wire without exceeding the proportional limit? b. How much will the wire stretch under this load? c. What is the maximum weight that the wire can support?
A steel cylinder (Est = 200 GPa and G = 79 GPa) undergoes an azial compression in which its diameter increases from 10 mm to 10.045 mm. If its final length is 123.00 mm, what was its original length?
The rigid beam of negligible weight is supported by a pin at O and two vertical rods. Find the vertical displacement of the P=70kips weight. a. What is the elongation in bronze? b. What is the elongation in Steel? c. Vertical displacement of load P? -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
A solid cylindrical rod 12 mm in diameter and 50 mm in length is attached to a rigid support at one end and twisted at its free end by 14°. If the Poisson’s ratio for this isotropic material is 0.34 and Young’s modulus is 70 GPa, what is the maximum shear stress induced?
A sign of mass 2,500-Kg hangs from the bottom end of a vertical cylindrical aluminum bar (with a diameter of 12-cm). (a) What is the stress within the bar? (b) What is the bar’s strain? (c) If the bar is 10-m long, how much is it lengthened?
To support a tensile load of 65 kN, a circular cross section and A metallic rod with a length of 0.32 m will be used. Stress in bar 240 MPa value and maximum elongation is desired to be 0.42 mm. In these conditions,what is the minimum diameter of rod [m]?(Elasticity for metallic bar Take the module as 220 GPa).
A circular rod of diameter 16 mm and 500 mm long is subjected to a tensile force 40kN. The modulus of elasticity for steel may be taken as 200 kN/mm2. Find stress, strain and elongation of the bar due to applied load.
A wire 4m long is stretched horizontally between points A and B 4m apart. A load W placed at the center of the wireproduces a sag of 53.4mm,a. If the wire is 25mm2 in cross-section and the Young’s modulus is 200GPa, what is the magnitude of load W? b. If the load was reduced by 40%, what will be the sag?
A straight bar of uniform cross sectionis tested in tension. The bar's cross sectional is 6.5 square centimeters and a length of 4 m. When the tensile load reaches 85kN, the total elongation is 2.5mm. What is the stress and the modulus of elasticity of the bar?
1. A circular rod of diameter 20mm and 500mm long is subjected to atensile force 50kN. The modulus elasticity for steel may be taken as 200kN/??2. Find stress and strain due to applied load.