Mention the basic flame types a

Q: ycle thermal ef

A: Givnen as,T=390°CP=9MPa

Q: ASE ANSWER WITH FULL SOLU

A: t=0.05in My=10×106in-lbs To-Find:- Shear Flow in wall AB

Q: How to find H available and H required? Using what formula? Briefly explain the calculation part.

A: Havailable=Ho-aQ2Ho=24.4a=0.0678 m/Lpm2

Q: In gas welding of a job, a neutral oxy-acetylene flame was used. If the acetylene consumption was 8…

A: Given, Type of flame = Neutral Acetylene consumption = CA = 8 litres   Let us take Oxygen…

Q: draulic pre eter and plun

A:

Q: MPa . Assumin H/m² and Poisso hange in diamet

A: Given data  Dia of pressure vessel =650 mm Internal pressure = 14.7 Modulus of elasticity = 200 GPa…

Q: What would it be in celcius

A: From the result, the final temperature of the air in the tank is 277.3 K

Q: 10. Complete sketch A to show the significance of the welding symbol shown in sketch B.

A: This is a double J weld Configuration Problem which consist of different radius on both side.

Q: pot

A:

Q: ur and

A:

Q: Gas welding equipment is bulky in nature and hence make it difficult to transport. Select one: True…

A: Gas welding equipment is bulky in nature and hence make it difficult to transport. Select one:…

Q: Which of the following does not belong to the group? force stress time velocity

A:

Q: fires

A: A spark is created when the applied electric field exceeds the dielectric breakdown strength of the…

Q: ent, of an alloy that consists

A: Atomic% of Cu =5% Atomic% of Pt= 95 % Required Wt% of above elements in alloys

Q: which among the following

A: Given: For an Oldham's coupling used between two shafts,Which statements are correct given in…

Q: Wo A L = 6R

A: For solution refer below images.

Q: the tip of the inner cone is the location of the maximum temperature in a neutral oxyacetylene…

A: Solution:   The Correct Option with necessary explanation is given below:

Q: to : 4) Horizontal component of pinch force tries Cause the arc blow Reduce the cross-section of the…

A: Pinch force :- The flow of current through the arc gap can produce or developed the electromagnetic…

Q: Q3. What is a welding process? Write the classification of welding process write any two advantages…

A:

Q: the power developed

A: Given: Under steady state:Specific enthalpy and velocity of steam at inlet and exit of a…

Q: the heat to raise the temperature to the melting point the heat to raise the molten metal to the…

A: Given: density=7.5 g/cm^3 melting point=800 oC specific heat, in solid state 0.33 J/gC in liquid…

Q: How much energy is added

A: To find The amount of energy added to the water by pump.

Q: 22. Which of the following would increase the amount of work done on an object? O increase the time…

A: Work done on the object can be calculated by  (force applied on object) × (distance travelled by…

Q: Refer to the diagrams to answer the following questions. 818 A B

A: Node: It is a point at which any standing wave has minimum amplitude. Antinode: It is a point at…

Q: What is the temperature of low

A: Given; A carnot cycle is having an efficiency of;  ηcarnot=0.75  High temperature reservior;…

Q: answer question 5)c)

A:

Q: On all CJP groove welds in butt joints transverse to the computed tensile stress, they: O A. Shall…

A: Introduction The Complete Joint Penetration (CJP) groove weld is a groove weld that extends…

Q: ut of tha

A:

Q: The example for forming process is ___________. a. Gas welding b. Extrusion c. Tempering d. Die…

A: Gas welding is a joining process which is use to join two different objects with each other…

Q: 3. Provide at least two distinctive definitions of two of the following terms:

A: Given Data : Job satisfaction leadership

Q: Match the following. Oxidizing Choose... flame Neutral Choose... flame

A: There are 3 types of flames in welding. 1) oxidising flame  2) carburizing flame  3) neutral flame

Q: a = -ks?,

A: 2/6 (ANSWER)

Q: Time required for the welding in sec

A: Given data; Inner diameter (do)=110 mmouter diameter (d1)=100mmPower supply (V)=30VRESISTANCE=42.4…

Q: Its coeffi

A:

Q: .1- Answer two of the following: a) What are deference between hot forming and cold fo

A: Hi and thanks for the question. Since you have asked multiple questions. As per the honour code, we…

Q: How much should we heat to close the gap

A: For the given system  Gap between rods (∆L) = 0.2 mm   To determine  Rise in temp to close the gap

Q: please use this steam table

A:

Q: Complete the following gas tables:

A: Given data  Given table

Q: . Complete the following gas tables:

A: Given data Given table

Q: °C. What is the distance of zero and 30 mark under these conditions?

A:

Q: a. Show how the extent of the surfacing weld is indicated between the vertical centerlines in the…

A: Writing the procedure to organise the weld between the lines on the flat. (1) Let us consider that…

Q: What is energy conversion used for ؟

A: Energy is present in many forms all around us such as electrical, kinetic, thermal, potential, and…

Q: What is the energy produced in MW per month of fuel

A: To determine  Energy produced/month

Q: ter at the d

A: Given : Diameter of jet = 2 cm = 0.02 m Area = a= πa4 Velocity = 25 m/s θ = inclination at outlet=…

Q: Give examples fof impact.

A: The definition of impact is one thing crashing into or having an effect on another.

Q: . The number of degrees of freedom

A: Given; From the given figure;   No. of D.O.F of the planetary gear train ;

Q: Which is the safest distance between the wall and the boiler? a. 5m  b. 1.5m c. 1m  d. 10m

A: SOLUTION BOILER IS  A MECHANICAL DEVICE THAT PRODUCES STEAM FOR THE TURBINE . `BOILER PRODUCES…