Refer to the figure shown. Determine the following considering the effect of the Prestressing force and Working loads simultaneously. 12 kN/m Section: 10 kN/m C.G. 750 mm 200 mm A B 8 m 7 m 350 mm a. Determine the ftop at x=8 m from left end. (MPa). b. Determine the fbot at x=8 m from left end (MPa).

Refer to the figure shown. Determine the following considering the effect of the Prestressing force and Working loads simultaneously. 12 kN/m Section: 10 kN/m C.G. 750 mm 200 mm A B 8 m 7 m 350 mm a. Determine the ftop at x=8 m from left end. (MPa). b. Determine the fbot at x=8 m from left end (MPa).

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.5P

See similar textbooks

Similar questions

Determine support reaction at B . Given P=100 Kn L=10 m
Determine support reaction. Given a=5 m b=10 m P=30 KN
Solve for: 1. Maximum W in kN if each leg resist 10.098 kN. 2. If W is 49 kN. what is the force resisting of leg DA? 3. If W is 51 kN. what is the force resisting of leg BA?
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=75° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm2 and A=50 cm2 shall be taken for all rods.)
A couple M of moment 8 kN·m acting in a vertical plane is applied to a W200 * 19.3 rolled-steel beam as shown. Determine (a) the angle that the neutral axis forms with the horizontal plane, (b) the maxi-mum stress in the beam
g.) What is the moment of inertia (I) about the neutral axis of the section? (in mm^4) h.)What is the first moment of an area (Q) about the neutral axis of the section? (in mm^3) i.)What is the maximum shearing stress (fv) of the beam? (in MPa)
A cantilever beam carries a trapezoidaldistributed load (see figure). Let wB = 2.5 kN/m,wA = 5.0 kN/m, and L = 2.5 m. The beam has amodulus E = 45GPa and a rectangular cross sectionwith width b = 200 mm and depth h = 300 mm.Use the method of superposition and Cases 1 and8 in Table H-1 to calculate the def lection and rotationat B.
An equilateral triangular plate of side 2.4m placed horizontally in a liquid (sp. gr. 0.80) in such a way that the center of the plate is 2.5m below the free surface of water. (a) Determine the area (in sq. meters) of the plate. (b) Determine the magnitude (in kN) of the resultant force on the plate.
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=30° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm² and A=50 cm² will be taken for all bars.)
The cantilever beam shown is subjected to a couple and 2 forces shown. Replace these couple and forces with an equivalent couple M and single force F at point A. Show solution to the answer FH = 1.64 kN, R Fv = 1.16 kN, D M = 2.22 kN-m, CCW
B: A tank containing water moving horizontally with a constant linear acceleration (3.5m/sec ), and vertical acceleration decreases by (25%) from the horizontal acceleration. The tank was (3m) high, (2.5m) length and (Im) width. Determine the force on the bottom of tank if the water level at rest was (2m). (Answer with sketch, See Fig.3)
THE ANSWER MUST BE IN FOUR DECIMAL PLACES the steef shaft shown in figure rotates at 4Hz with 35 KW taken off at A, 20 kW removed at B and 55 kW applied at C. Using G=83 GPa, find the maximum shearing stress and the angle of rotation of gear A relative to gear C