Replace the force system acting on the pipe assembly by a resultant force FR and couple moment MR at point O as shown in (Figure 1). Take F₁ = {-25i-10j + 25k}lb, F₂= {-15i+25j +20k}lb. Figure 2 ft 2 ft < 1 of 1 > میں 2 Part A Determine the resultant force FR. Enter the x, y, and components of the force separated by commas. Express your answers in pounds to three significant figures. -- ΑΣΦ FRZ. FRY, FR== Submit Part B Request Answer MRoz MRoy MRo, z = Submit Provide Feedback vec Determine the couple moment MR. Enter the x, y, and z components of the moment separated by commas. Express your answers in pound-feet to three significant figures. Request Answer 195| ΑΣΦ. 11/ www. vec ? lb ? lb ft Next >

Replace the force system acting on the pipe assembly by a resultant force FR and couple moment MR at point O as shown in (Figure 1). Take F₁ = {-25i-10j + 25k}lb, F₂= {-15i+25j +20k}lb. Figure 2 ft 2 ft < 1 of 1 > میں 2 Part A Determine the resultant force FR. Enter the x, y, and components of the force separated by commas. Express your answers in pounds to three significant figures. -- ΑΣΦ FRZ. FRY, FR== Submit Part B Request Answer MRoz MRoy MRo, z = Submit Provide Feedback vec Determine the couple moment MR. Enter the x, y, and z components of the moment separated by commas. Express your answers in pound-feet to three significant figures. Request Answer 195| ΑΣΦ. 11/ www. vec ? lb ? lb ft Next >

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bent rod is supported at points A, B and C by smooth journal bearings, and is subjected to force F. If dimensions a = 2.3 m, b = 1.5 m, c = 0.6 m, and d = 2.5 m, and the force F is {-2i + 9j - 3k} kN, determine the magnitude of the moment (in kN⋅m) caused by force F about point A. Answer must include 2 places after the decimal point.
Which of the following gives the moment MD about point D of the tensile force TBA exerted by the wire at point B? Note that rB/D = (4i - 6k) m and TBA = (-8i + 6j + 4k) kN and that MD = rB/D x TBA. a. (36.0i + 32.0j + 24.0k) kN-mb. (48.0i + 24.0j + 16.0k) kN-mc. (-36.0i - 32.0j - 24.0k) kN-md. (16.0i - 12.0j -8.0k) kN-m
ONLY ANSWER 1, 2 & 3!!!!!!!!!!!!!!!!! 1.The problem sketch shows _____ loads. 2.The moment load (the couple) has a magnitude of _____ N*m. 3.The resultant moment induced by all of the loads has a magnitude of _____ N*m.
C0nsider the frame bel0w where f0rce A = 55 N acts 0n point Q, force B = 34 N acts 0n p0int P, and f0rce C = 42 N acts on point M. Replace the system of f0rces acting on the frame with an equivalent force-c0uple system acting at point O. Calculate for the moment of the c0uple of transfer and magnitude and direction of the resultant f0rce
Find the equivalent resultant force and couple moment of the force system about point C, given: F1 = 65 N, F2 = 95 N, AX = 4 m, AY = 3 m, BX = 5 m, BY = 6 m, CX = 3 m, CY = 2 m, θ = 25 °, x,y,h = 12,5,13, respectively The magnitude of resultant force, FR is: FR = The angle of the resultant force as measured from the positive x-axis is: (Note, in quadrant 1 or 2, the angle should be beween 0 and 180 degrees, while in quadrant 3 or 4, the angle should be between 0 and -180 degrees). θR = The resultant moment about point C is: MRC =
In the assembly shown, member AB is rigidly attached to the wall while an L bar is pinned to AB at E. Two forces P and Q are acting on the assembly as shown. Force P lies on the x-axis while force Q is applied at point D along a plane parallel to the yz plane. 1. Which of the following quantities is/are zero? (Choices: A. Moment of P about the x-axis ; B. Moment of P about the y-axis ; C. Moment of P about the z-axis) 2. Which of the following best approximates the moment of force Q about point A? 3. Which of the following best approximates the equivalent force-couple set at point A of the applied forces P and Q? Note: F is the resultant force and Cis the resultant couple4. Considering the force diagram of member DE, which gives the complete set of reactions for the support at E? (Note difference of Force and couple reactions)
The force P is applied to the lever which controls the auger of a snow blower. Determine themagnitude and direction of the smallest force P which has a 2.20 N-m clockwise moment about A. Figure:3
Cables OA, OB, OC, and the vertical cable, knotted at O, support the 108lb weight. Cables OA and OB lie in the x-y plane. Sketch a complete free body diagram knot at O. Select the expression that describes the tension in cable OC, acting at O, as a Cartesian vector. a. - 3/13 Toc i + 4/13 Toc j + 12/13 Toc k b. 3/5 Toc i + 4/5 Toc j c. -Toc j d. - 3/13 Toc i + 12/13 Toc j + 4/13 Toc k
The ends of the triangular plate are subjected to three couples. Determine the magnitude of the force F so that the resultant couple moment is 500 N.m clockwise Please include a Freebody Diagram, Proper Labels, Givens and Solution
- Two different ropes connected to the A ring, FB and FC as in the figure. pulling forces are applied. (ring A is in the x-y plane and its z coordinate is zA =0.) Accordingly, a-) Express the FB force as vector. b-) Vectorial moment of FC force with respect to point B Calculate as. FB=(26)kN, FC = (12)kN, hB = (7)m, hC=(8)m
The rigid pipe is subject to the following loads. Neglecting the weight of the pipe, determine the moment at O. SOLVE THE FF Vector component form of 50-lb force (ANSWER: 25.000i +0j -43.30k lb) Magnitude of the resultant force (ANSWER: 78.10 lb) Position vector of the 50-lb force from point O to its point of application on the pipe. (ANSWER: -15i -10j +12k inch) Moment at point O, in vector component form. (ANSWER: 1153.01i -829.52j +250.00k lb-in)
The member is supported by a square rod which fits loosely through the smooth square hole of the attached collar at A and by a roller at B. The member is subjected to the forces F1 = 200 N , F2 = 350 N , and F3 = 500 N . Determine the normal reaction force of roller at B. Determine the components of the reaction force of the support at A using scalar notation. Determine the components of moment of the reaction at A using scalar notation.