192.407 N*m was wrong !Required informationA torque T is applied to the 20-mm-diameter steel rod AB. Assume the steel to be elastoplastic with G= 77.2 GPa and ry=145 MPa. Consider L = 2.75 m.20 mmDetermine the torque T when the angle of twist at A is 25º.The torque T when the angle of twist at A is 25° is 192.407 N.m.

Answered: Image /qna-images/answer/e6f92dcb-a9b1-45f9-a42e-766baacf8574.jpg

Required information A torque T is applied to the 20-mm-diameter steel rod AB. Assume the steel to be elastoplastic with G= 77.2 GPa and Ty= 145 MPa. Consider L = 2.75 m. 20 mm Determine the torque T when the angle of twist at A is 25°. The torque T when the angle of twist at A is 25° is 192.407 N-m.

Required information A torque T is applied to the 20-mm-diameter steel rod AB. Assume the steel to be elastoplastic with G= 77.2 GPa and Ty= 145 MPa. Consider L = 2.75 m. 20 mm Determine the torque T when the angle of twist at A is 25°. The torque T when the angle of twist at A is 25° is 192.407 N-m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Topic: Thermal & Torsional Stress The four gears are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20 kW are used by gear A, 20 kW by gear C, and 30 kW by gear D. (a) Find the uniform shaft diameter if the shear stress in the shaft is not to exceed 60 MPa. (b) If a uniform shaft diameter of 100 mm is specified, determine the angle by which one end of the shaft lags behind the other end. Use G = 83 GPa for steel.
A steel specimen of 12 mm diameter extends by 6.31 x 10-2 mm over a gauge length of 150 mm when subjected to an axial load of 10 kN. The same specimen undergoes a twist of 0.5° an a length of 150 mm over a twisting moment of 10 N-m. Using the above data, determine the elastic constants E, Mu, G and K.
Torsional T is applied to the hollow axis (G=80 GPa). Ewha Womans University, the maximum shear strain is γmax = 640 × 10-6rad Igo, inside andThe outside diameters are 120mm and 150mm, respectively.a. What is the maximum axial strain?b. Maximum axial stress?c. What is the maximum torque (T) meeting the above conditions?
A solid cylindrical rod 12 mm in diameter and 50 mm in length is attached to a rigid support at one end and twisted at its free end by 14°. If the Poisson’s ratio for this isotropic material is 0.34 and Young’s modulus is 70 GPa, what is the maximum shear stress induced?
A circular shaft having a diameter of 4 in. is subjected to a torque of 250 kip # in. If the material is elastic perfectly plastic, with tY = 16 ksi, determine the radius of the elastic core.
A solid shaft is subjected to a twisting moment of 350 kNm. If the angle of twist is 5° per meter of the shaft and the shear stress is not to exceed 350 MPa. Determine the suitable shaft diameter by comparing the strength design and rigidity design. Also, determine the maximum shear strain acting on the shaft. Take G =225 GPa.
mechanics of rigid bodies The shaft assembly is made from a steel tube 1 in. in diameter, which is bonded to a solid brass core 0.5 in. in diameter. If a torque of 250 lb-ft is applied at its end, determine the maximum shear stress in psi experienced by the assembly. Take G for steel at 11.4x103 ksi and G brass at 5.2 x 103 ksi. with diagram if necessary.
A solid steel post is subjected to pure torsion. Given: -post Diameter = 65 mm -length = 2.75 m -torque = 2.4 kN-m -shear Modulus of Elasticity = 78 GPa Question: What is the Angle of Twist in degrees?
– The weight is suspended from structural A–36 steel alloy and 2014-T6 aluminum alloy wires, eachhaving the same initial length of 10 ft and cross-sectional area of 7×10–3 in2 (Figure Q1). If the weight is increasedgradually, determine which wire yields first? Explain which material model and yield criterion you will use? Justifyyour choices
(a) A 25 mm diameter bar is subjected to an axial tensile load of 100KN. Under the action of this load a 200 mm gauge length is found to extend 0.19 x 10-mm. Determine the modulus of elasticity for the bar material. (b) If, in order to reduce weight whilst keeping the external diameter constant, the bar is bored axially to produce a cylinder of uniform thickness, what is the maximum diameter of bore possible given that the maximum allowable stress is 240 MN/mo? The load can be assumed to remain constant at 100kN. (c) What will be the change in the outside diameter of the bar under the limiting stress quoted in (b)? (E = 210 GN/m2 and 1 = 0.3).
A drill rod with a diameter of 12 mm is made of high-strength steel alloy with a shear modulus of 80 GPa. The rod is to be subjected to a torque T. What is the minimum required length L of the rod so that the cross section at one end can be rotated 90⁰ with respect to the other end without exceeding an allowable shear stress of 300 MPa?
A shaft of radius c = 0.75 in. is made from an elastic perfectly plastic material as shown. Determine the torque T that must be applied to its ends so that it has an elastic core of radius r = 0.6 in. If the shaft is 30 in. long, determine the angle of twist.