Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable Five kilograms of air at 427°C and 600 kPa are contained in a piston-cylinder device the pressure is 100 kPa and produces 450 kJ of work output. Assume air has constar termine the entropy change of the air in kJ/kg-K. Use the table containing the ideal gas u must provide an answer before moving on to the next part.)

Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable Five kilograms of air at 427°C and 600 kPa are contained in a piston-cylinder device the pressure is 100 kPa and produces 450 kJ of work output. Assume air has constar termine the entropy change of the air in kJ/kg-K. Use the table containing the ideal gas u must provide an answer before moving on to the next part.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Starting with the First Law of Thermodynamics, derive the complete expression for the change in entropy for an ideal gas process. Then describe how it reduces for the four processes that we have studied
P25. 200 kg/h of air is compressed adiabatically, assuming that ∆ ep = 0. The fluid enters the compressor at 0.9 Bar and 17°C, and leaves it at 750 kPa and 187°C. Make a diagram appropriate to the statement, calculate the input/output ratio so that ∆ec is negligible and determine the power delivered to the compressor.
Saturated vapor water at 100 kPa enters an isentropic compressor and exits at 2 MPa. Note that isentropic implies adiabatic and reversible. 1. What is the specific entropy of the inlet, in kJ/kg K? 2. What is the specific entropy of the outlet, in kJ/kg K? 3. What is the temperature of the outlet in °C. Round to one decimal place. 4. How much work, in kJ/kg, must be used for this process? Round your answer to one decimal place.
In the course of pumping up a bicycle tire, a liter of air at atmospheric pressure is compressed adiabatically to a pressure of 7 atm. (Air is mostly diatomic nitrogen and oxygen.)(a) What is the final volume of this air after compression?(b) How much work is done in compressing the air?(c) If the temperature of the air is initially 300 K, what is the temperature after compression?
1. An engine from a quarry vehicle used in the Build a Beach program of DEMR has a power requirement of 560 kW. Per hour of its operation, it ejects 234 MJ into its surroundings at 50 °C. If it behaves like a Carnot engine, answer the questions below. A. How much work (MJ) is done by the engine per hour of operation? B. What is the efficiency (%) of the engine?C. What is the temperature (°C) of the hot reservoir? 2. Determine the entropy change (kJ/K) associated to the conversion of 10 kg of ice at -11 °C to steam at 121 °C. 3. Anna and Beth are using another rare metal, the nth metal (c = 0.600 J/g-℃), to build the 5-kg cuirass of their design. Initially, the metal is at 2250 K. It is then submerged to 10 kg of water at 15 °C. If the remaining liquid water after submerging the metal is 8.5 kg, solve for the net entropy change (kJ/K) of the system.
Air at 7°C enters a turbojet engine at a rate of 16 kg/s and at a velocity of 220 m/s (relative to the engine). Air is heated in the combustion chamber at a rate 15,000 kJ/s, and it leaves the engine at 427°C. Determine the thrust produced by this turbojet engine. (Hint: Choose the entire engine as your control volume.)
10. Steam at 173.46 degrees celcius and with a specific entropy of 6 kJ/ kg K undergoes a polytropic process with n= 1.18 until the pressure becomes 2 MPa. (a) What is the final temperature of the steam? (b) What is the work and the quantity of the heat of the process? NOTE: - INDICATE THE PV and TS DIAGRAM - INDICATE THE INITIAL AND FINAL STATE OF THE SUBSTANCE.
Select the correct expression for steady flow work of a reversible compressor_________ A. B. C. D.
HANDWRITTEN AND THE FINAL ANSWER SHOULD BE IN ENGLISH SYSTEM Engr. Darmis is tasked to design a frictionless and constant temperature steady-flow system that will be used for power generation using Nitrogen as its working fluid. The initial gage pressure is 115 pounds per square inch and the final volume is 170 cubic feet. If ninety-two pound-mass of the fluid gain 3.253 BTU/R of entropy per minute. Find the (a) initial volume, (b) temperature, and (c) Work. (d) If the heat is equal to 9980 BTU, how long did the process took place?
THERMODYNAMICS A 1.5-kW power output is produced by a small, high-speed turbine that runs on compressed air. The entrance state is 400 kPa and 52 degrees celcius, whereas the exit state is 150 kPa and -43 degrees celcius. Determine the needed mass flow rate of air through the turbine assuming low velocities and an adiabatic process.
Given 603.06 kW electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 1.5(105) W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Total rate of entropy production= 1.256 kJ/s K. Total rate of exergy destruction= 368.37 kW. Consider steady state conditions. 1.4) 0.015 kg is the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to the conditions of the problem above. if the electrical heating device is replaced with a gas fired boiler. The high heating value (HHV) of the fuel is 50.02 MJ/kg. Answer the following: a) Calculate the exergy destroyed in the process described by problem 1.4. The exergy of the fuel entering this process is 51.82 MJ/Kg. The dead state…
Hydrogen enters a steady-ﬂow and adiabatic compressor at 310 K and 95 kPa and exits at a pressure of 400 kPa. The amount of work required is 2400 kJ/kg of hydrogen. Assume that speciﬁc heats are evaluated at the inlet temperature. What is the outlet temperature, in K? Report your answer to one decimal place using rounding and use an appropriate amount of significant figures for intermediate calculations. Calculate the amount of entropy generated in kJ/kg K. Round to three decimal places.