Required information Three forces are applied to the bar shown. Take P= 46 kips. P 0.9 in.1 0.9 in. h = 10.5 in. 1.2 in. 1.2 in. 4.8 in. 2 kips C 2.4 in. 6 kips 2 in. 1.8 in. ksi. Determine the normal and shearing stress at point c. (Round the final answers to three decimal places.) The normal stress at point cis The shearing stress at point cis ksi.

Required information Three forces are applied to the bar shown. Take P= 46 kips. P 0.9 in.1 0.9 in. h = 10.5 in. 1.2 in. 1.2 in. 4.8 in. 2 kips C 2.4 in. 6 kips 2 in. 1.8 in. ksi. Determine the normal and shearing stress at point c. (Round the final answers to three decimal places.) The normal stress at point cis The shearing stress at point cis ksi.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Using the shear formula, how can we check that the allowable shear stress is not exceeded?
How can the maximum shear stress be determined ?
W310 x 52 beam is made with a material that has a maximum shearing stress of 90 MPa. Determine the maximum shearing force.
A single bolt is used to lap joint two steel bars together. Tensile force on the bar is 20,000 N. Determine the diameter of the bolt required if the allowable shearing stress is 70 MPa?
A timber beam, 80mm wide by 60mm high, is subjected to a vertical shear load of V = 40KN. Determine the shearing stress developed at layers 20mm apart from top to bottom of the section. pls answer with complete solution thank you
why do you multiply by 16 in the shear stress?
If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the diameter (mm) of the A premium?
What is the linear variation in shear stress along any radial line?
PART 2: Determine the shear force acting at each of the following locations: (a) x = 0+ ft (i.e., just to the right of support A) (b) x = 14.0 ft (i,e., at point B.) (c) x = 20.5- ft (i.e., just to the left of the support C) (d) x = 20.5+ ft (i.e., just to the right of the support (C) (e)x=27.5ft Note that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2. My Answers: Correct (a) V= 105.823 kips (b)V= -48.177 kips (c) V= -119.677 kips (d)V= 88 kips (e) V= 10.9998 kips PART 3: Determine the bending moment acting at each of the following locations: (a) x = 14.0- ft (i.e., just to the left of point B.) (b) x = 14.0+ ft(i.e., just to the right of point B.) (c) x = 20.5 ft (i.e. at point C) (d)x=27.5ft Note that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2. My Answers: Correct (a) M = 403.522 kips-ft (b) M = 193.522 kips-ft (c) M = -352.0035 kips-ft (d) M =…
Design the rectangular key for a shaft of 50mm diameter. The shearing and crushing stresses for the key material are 42MPa and 70MPa. Determine the length in mm. From Table 13.1, we find that for a shaft of 50mm diameter, the Width of the key. w=16mm and thickness of the key, t=10mm
Help me determine Maximum shear stress
A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb. Determine the magnitude and location of the highest bending and torsional stresses in the 1" diameter shaft.