I need the answer as soon as possible I ReviewThe two bars shown in the figure below (Figure 1) are made of amaterial that has the stress-strain diagram shown. (Ekuta 2)Part AIfthe cross-sectional area of bar AB is 2.4 in" and BC is 5.0 in', determine the largest lorce P that can be supported before any member fractures. Assumethat buckling does not ooour.Express your answer to three significant figures and include appropriate units.P= ValueUnitsSubmitRequest AnswerProvide FeedbackNext >Figure1 ot 2 >a (ksi)2520-15compression105ptension- e (10~*) (in./in.)0.200.400.60 0.75

Answered: Image /qna-images/answer/4aebac0b-50aa-4433-a7bb-6978189cd136.jpg

Revier The two bars shown in the figure below (Figure 1) are made of a material that has the stress-strain diagram shown. Eaute 2) • Part A he cross-sectional area of bar AB is 24 in' and BC is 5.0 in', determine the largest force Pthat can be supporled before any member fractures. Ass that buckling does not ooour. Express your answer to three significant figures and inciude appropriate units. Value Units Submit Request Answer

Revier The two bars shown in the figure below (Figure 1) are made of a material that has the stress-strain diagram shown. Eaute 2) • Part A he cross-sectional area of bar AB is 24 in' and BC is 5.0 in', determine the largest force Pthat can be supporled before any member fractures. Ass that buckling does not ooour. Express your answer to three significant figures and inciude appropriate units. Value Units Submit Request Answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A square bar of wrought iron, 2 inches on each side, is raised to a temperature of 100 deg F above its normal. If held so that it cannot expand, K = 6.8 x 10-6 per deg F. What is the force necessary to prevent expansion? The modulus of elasticity E may be taken as 30 million psi. ( Answer : 81,600 lb)
The ply stress σα was calculated for AS1/3501-6 Graphite/Epoxy laminates [0/+-45]s under load with N1=10,000 N/m and N2=N6=0. When the strength of this material is as follows, determine the stability of the laminate according to the maximum stress theory.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure 1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (σY)st=680MPa, and for the bronze (σY)br=490MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa. Express your answer to three significant figures and include appropriate units.
A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to2.01 m. The true axialstrain is?
2. A bar of thickness 15mm and having a rectangular cross-section carries a load of 120kN. Determine the minimum width of the bar to limit the stress to 200MPa. The bar, which is 1m long, extends by 2.5mm when carrying a load of 120kN. Determine the modulus of elasticity of the material of the bar.
A tensile force. of 120 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter decreases to 0.01998 m and the length increases to 2.01 m. The true stress on that rod is?
A horizontal steel I – beam of cross-sectional area 0.041m2 is rigidly connected to two vertical girders. If the beam was installed when the temperature was 300C, what stress is developed in the beam when the temperature drops to - 300C? (b) Is the ultimate strength of the steel exceeded? (c)What stress is developed if the beam is concrete and has a cross- sectional area of 0.13m2 ? Will it fracture?
Name the phenomenon that occurs when a metal is loaded wellwithin the elastic range at a temperature of 800°F (427°C) and it slowly deforms permanently.
A steel rod with a cross-sectional area of 180 mm2 is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 10-6 mm/ (mm°C) and E = 200 GPa. Which of the following most nearly gives the temperature at which the compressive stress will be 48 MPa? Which of the following most nearly gives the temperature at which the tensile stress will be 48 MPa? Which of the following most nearly gives the temperature at which the stress will be zero?
The cable of hoist has a cross sectional of 80mm2.The hoist is used to lift a crate weighining 500 kg.The free length of of the cable is 30 m.Assume all deformation is elastic. (a) what is the stress on the cable. (b) How much will the cable extend if it is made from steel(E-200 Gpa)? (c) How much will the cable extend if it is made from polypropylene(E-1.2 Gpa)?
Knowing that the central portion of the BD bar has a uniform cross-sectional area of 800 mm^2 determine: A)The Elasticity module of the BD bar (see graph σ x E). Explain your calculations. B) The maximum shear stresses are normal and DB. C)Determine the shear stress on pin B, knowing that the diameter of the pin is 20 mm.
A tensile force of 10 kN is applied on a 0.02-m diameter and 2-m long rod. After applying theload, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. The lateral (transverse) strain is?