Rigid bar ABC shown in the figure is supported by a pin at bracket A and by Se has a diameter of 6 mm, and it is supported by double-shear pin connections at Band. The pe at bracket A is a single-shear connection. All pins are 8 mm in diameter. 0-60 Extens shear stress in pin B. Answer in MPa rounded-off to 2 decimal places a a = 65 centimeter b = 32 centimeter h = 58 centimeter P = 785 Newton B b h

Rigid bar ABC shown in the figure is supported by a pin at bracket A and by Se has a diameter of 6 mm, and it is supported by double-shear pin connections at Band. The pe at bracket A is a single-shear connection. All pins are 8 mm in diameter. 0-60 Extens shear stress in pin B. Answer in MPa rounded-off to 2 decimal places a a = 65 centimeter b = 32 centimeter h = 58 centimeter P = 785 Newton B b h

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.13P: A metal bar AB of a weight Ills suspended by a system of steel wires arranged as shown in the...

See similar textbooks

Similar questions

A ship's spar is attached at the base of a mast by a pin connection (see figure). The spar is a steel tube of outer diameter d2= 3.5 in. and inner diameter d1= 2.8 in. The steel pin has a diameter d = 1 in., and the two plates connecting the spar to the pin have a thickness t = 0.5 in. The allowable stresses are compressive stress in the spar. 10 ksi: shear stress in the pi n, 6.5 ksi: and bearing stress between t he pin and t he connecting plates, 16 ksi. Determine the allowable compressive force Pallowin the spar.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
Two boards are joined by gluing along a scarf joint, as shown in the figure. For purposes of cutting and gluing, the angle a between the plane of the joint and the faces of the boards must be between 10° and 40f. Under a tensile load P, the normal stress in the boards is 4.9 MPa. (a) What axe the normal and shear stresses acting on the glued joint if a = 20°? (b) If the allowable shear stress on the joint is 2.25 MPa. what is the largest permissible value of the angle ct? (c) For what angle a with the shear stress on the glued joint be numerically equal to twice the normal stress on the joint?
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A solid circular bar is fixed at point A. The bar is subjected to transverse load V = 70 lb and torque T = 300 lb-in. at point B. The bar has a length L = 60 in. and diameter d = 3 in. Calculate the principal normal stresses and the maximum shear stress at clement 1 located on the bottom surface of the bar at fixed end A (see figure), Assume that element 1 is a sufficient distance from support A so that stress concentration effects are negligible
At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
A post having a hollow, circular cross section supports a P = 3.2 kN load acting at the end of an arm that is h = 1.5 m long (see figure). The height of the post is L = 9 m, and its section modulus isS = 2.65 x 10 mmJ. Assume that the outer radius of the post is r2= 123 mm, and the inner radius is r}=117 mm. (a) Calculate the maximum tensile stress and \ maximum in-plane shear stress Tm:ls at point A on the outer surface of the post along the x axis due to the load P. Load P acts at B along line BC. (b) If the maximum tensile stress and maximum in-plane shear stress at point A arc limited to 90 MPa and 38 MPa, respectively, what is the largest permissible value of the load PI
A traffic light and signal pole is subjected to the weight of each traffic signal We = 45 lb and the weight of the road lamp WL= 55 lb. The pole is fixed at the base. Find the principal normal stresses and the maximum shear stress on element B located 19 ft above the base (see figure). Assume that the weight of the pole and lateral arms is included in the signal and lamp weights