Rigid member AB is supported by hinge support at A and a 12-mm-diameter wire BC at B as shown. The diameter of the pin at A is 10 mm, thickness of member AB is 20 mm, and the thickness of each bracket of support A is 15 mm. Use a factor of safety FS= 2 and following failure stresses to determine the maximum load w (kN/m) the member can support. For wire BC: G=350 MPa Pin at A: T200 MPa Support brackets: (Gaarna ka=150 MPa d-12 -35m -3m

Rigid member AB is supported by hinge support at A and a 12-mm-diameter wire BC at B as shown. The diameter of the pin at A is 10 mm, thickness of member AB is 20 mm, and the thickness of each bracket of support A is 15 mm. Use a factor of safety FS= 2 and following failure stresses to determine the maximum load w (kN/m) the member can support. For wire BC: G=350 MPa Pin at A: T200 MPa Support brackets: (Gaarna ka=150 MPa d-12 -35m -3m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.4.16P: An aluminum tube AB with a circular cross section has a sliding support at the base and is pinned at...

See similar textbooks

Similar questions

Determine the allowable axial load Pallowfor a steel pipe column that is fixed at the base and free at the top (see figure) for each of the following lengths: L = 6 ft, 9 ft, 12 ft, and 15 ft. The column has an outside diameter d = 6.625 in. and wall thickness t = 0.280 in, (Assume E = 29,000 ksi and y= 36 ksi.)
An aluminum tube AB with a circular cross section has a sliding support at the base and is pinned at the top to a horizontal beam supporting a load Q = 200 kN (sec figure). Determine the required thickness t of the tube if its outside diameter d is 200 mm and the desired factor of safety with respect to Eu 1er buckling is n = 3.0. (Assume E = 72 GPa.)
A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.
An aluminum strut 2.50m long has a rectangular section 60mm by 30mm. A bolt through each end secures the strut so that it acts as a hinged column about an axis perpendicular to the 60 mm dimension and as a fixed ended column about an axis perpendicular to the 30mm dimension. Determine the safe central load using a factor of safety of 2.5 and E = 70 Gpa.
A solid aluminum [E = 64 GPa] rod (1) is connected to a solid bronze [E = 114 GPa] rod (2) at flange B, as shown. Aluminum rod (1) has an outside diameter of 36 mm and bronze rod (2) has an outside diameter of 17 mm. The normal stress in the aluminum rod must be limited to 124 MPa, and the normal stress in the bronze rod must be limited to 92 MPa. Assume L1 = 168 mm and L2 = 399 mm. Determine: (a) the maximum downward load P that may be applied at flange B. (Answer: P = 146kN)(b) the deflection vB (downward is positive) of flange B at the load determined in part(a). (Answer: vB = .322 mm)
A suspension system of a mountain bike is held by a pin at point C and supported by a shock absorber BD. If the bike is designed to withstand a load P = 1500N with safety factor FS = 2, ultimate shear stress τu = 150 MPa and ultimate tensile stress σu = 360 Mpa, determine pin B and pin C diameters
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 2850 mm2 and an allowable normal stress of 105 MPa. Bar (2) has a cross-sectional area of A2 = 3950 mm2 and an allowable normal stress of 160 MPa. Assume x1 = 1.9 m, x2 = 2.7 m, y1 = 1.5 m, and y2 = 2.6 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
A suspension system of a mountain bike is held by a pin at point C and supported by a shock absorber BD. If the bike is designed to withstand a load P = 1500N with safety factor F₁ = 2, ultimate shear stress t = 150 MPa and ultimate tensile stress Ou = 360 Mpa, determine pin B and pin C diameters.
A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 70 lb/ft^2 against the full area of the sign. The dimensions of the poles and sign are h1 = 16 ft, h2 = 7 ft, and b = 13 ft. To prevent buckling of the walls of the poles, the thickness t is specified as one tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7100 psi in the aluminum. Round your answer to two decimal places. d = ___ in. (b) Determine the minimum required diameter based upon an allowable shear stress of 2100 psi. Round your answer to two decimal places. d = ___ in.
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 4850 mm2 and an allowable normal stress of 150 MPa. Bar (2) has a cross-sectional area of A2 = 4750 mm2 and an allowable normal stress of 140 MPa. Assume x1 = 2.2 m, x2 = 3.4 m, y1 = 1.1 m, and y2 = 2.7 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.Answer: Pmax = Enter your answer in accordance to the question statement kN
2. A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determinethe outside diameter of the tube if the stress is limited to 120 MN/m2.
Q#3. An aluminium strut 16 ft long has a rectangular cross section 2 in by 3.5 in. A bolt through each end secure the strut in such a way that is acts as hinged column about an axis perpendicular to 3.5 in dimension; and as fixed column about an axis perpendicular to 2 in dimension. Determine the safe central load with a factor of safety of 2 and E= 10300000 psi. Also discuss in detail about the governing column capacity and reasons behind it.