SYSTEM AND CONTROL (MECHANICAL) (SA2)Gear B and C are mounted on a central shaft and they rotate at the samespeed/as a unit. Gear A is the driver and gear D is driven.Driver Gear (10 Teeth)Driven Gear (50 Teeth)QueshionsIf gear A rotates in a clockwise direction, to which direction will gear Crotates?1(2).2 If gear B rotates in an anti-clockwise direction, to which direction willgear C rotates(2)3Calculate the gear ration of the system(6).4Draw the systems diagram of the above mechanism(6)[16]

Given Gear train To find A rotates clockwise C rotates B rotates anticlockwise C rotates Gear ratio…

Answered: river Gear (10 Teeth) Driven

Engineering

Mechanical Engineering

river Gear (10 Teeth) Driven

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter38: Manual Transmissions And Transaxles

Section: Chapter Questions

Problem 5ASRQ: Technician A says that if a single idler gear is used to obtain reverse gear, its size and number of...

See similar textbooks

Related questions

Q: A planetary gear box is needed to provide 30:1 increase the speed, while minimizing the overall…

A: Given: A planetary gear box

Q: A gear has 44 teeth of the 20°, full-depth, involute form and a diametral pitch of 12. Compute the…

Q: Evaluate the number of teeth of gear D.

Q: State an equation tha relate the number of teeth of gear D, B and C.

Q: Two mating external 8-pitch, 20o , spur gears have 24 and 64 teeth. Determine the contact ratio.

Q: 1. Solve for the following pitch cone angles if the miter gears has 18 teeth.

A: Given: The number of teeth of the mitre gear: →Z=18 Because mitre gear has the property that both…

Q: nning at 100 rpm clockwise. B is an output shaft running at 250 rpm clockwise. Torque on A i

A: given:NA=100RPMNB=250RPMTA=50KN-m

Q: Q: A bevel gear has the following data. face width-35mm, hub diameter=80mm, shaft diameter%350mm,…

Q: addendum,

A: Complete solution given in below files.

Q: A 14.5 degrees full-depth involute gear has an outside diameter of 5-1/3 in. and diametral pitch of…

Q: A compound spur gear train is made up of a set of gears as indicated in the sketch using an input…

Q: Problem 1: A gear has 44 teeth of the 25° full-depth, involute form and a module of 4. Compute the…

A: Given: Number of teeth on a gear, T=44 module, m = 4 Gear System: 250 Full depth, involute…

Q: Problem 1: A gear has 44 teeth of the 25° full-depth, involute form and a module of 4. Compute the…

Q: n epicyclic gear train, as shown in Fig.

Q: full depth gear tooth of 20° pressure angle has standard addendum. Dedendum is 1.25 times of module.…

A: Given, Pressure angle = φ = 20o Module = m = 2.5 mm Addendum = a = m = 2.5 mm (For standard addedum,…

Q: A 20 straight-tooth bevel pinion 32-tooth gear. The two shafts are a (a) The cone distance (b) The…

Q: picyclic gear in Fig. 11. er of teeth on 0 and 200. De

Q: A spur gear has a pitch diameter 3. Calculate its working Depth.

Q: Two internal 10-pitch, 20° full-depth gears are used in a system. The pinion has 28 teeth and the…

A: Given Data The number of teeth on pinion is:t1=28 The number of teeth on the gear is:t2=70 The…

Q: A helical gear has a normal diametral pitch of 24, a normal pressure angle of14 14,°. 72 teeth, a…

Q: Begin a full-size layout of a pair of spur gears having a 4:1 velocity ratio, a 10-in center…

Q: Mcq: the main type of stress in gear tooth is ? A-shear stress B-tensile stress C-bending and…

A: These questions are based on the concept of Gear and mode of gear failure.

Q: State two advantages of a compound gear train over a simple gear train

A: Given: One gear train is simple gear train and other gear train is compound gear train. Determine:…

Q: The ratio of Number of teeth to pitch circle diameter is called

A: (1) Module: It is the fraction of the diameter d of pitch circle to the number of the teeth T of the…

Q: A gearset consists of a 16-tooth pinion driving a 40-tooth gear. The diametral pitch is 2, and the…

A: Teeth of pinion = 16 Teeth of gear = 40 pitch diameter = 2 pressure angle = 20o

Q: Twenty degree full depth involute profiled 19-teeth pinion and 37-teeth gear are in mesh. If the…

A: Given:Teeth on pinion, Tp=19Teeth on gear, Tg=37module, m=5 mm

Q: 2-) Answer the following questions a-) The number of teeth that the gear wheels will have at least…

Q: ratio factor Q for these gears

A: Given D1=100 , D2=400, D3= 100 , D4= 400 Module m = 4mm So, No. of teeth on each gears, m= D/T T…

Q: Q3:- The increase of the contact ratio is desirable in gearing design because of:- * All of these…

A: As per our guidelines we are supposed to solve one question per post. Kindly repost second question…

Q: Choose the correct answer Mcq: the main type of stress in gear tooth is ? A-shear stress B-tensile…

A: what are the main stresses in the gear tooth.

Q: triple thread worm used in a gearset has a pitch diameter of 2.5 and a lead of π/5 in. Which of the…

Q: A 20° full-depth, involute spur gear with 18 teeth has a diametral pitch of 12. Determine the…

A: Given Data:- Find:-Angle ϕ = 20° (a) Pitch Circle dia…

Q: Given: No. Of teeth= 18 Addendum= 2mm Solve for the following: a.Module b.Diametral pitch…

A: As per bartleby guidelines we are allowed to solve only 1st 3 subparts if multiple subparts are…

Q: gear ratio 1:20 motor RPM 980 7.5hp torqe=1500n/m worm gear design find the number of teeth and each…

Q: Clearly explain the directions for forces on mating spur gears mounted on two parallel shafts. Draw…

A: Introduction Spur gears are a type of cylindrical gears with straight teeth and are mounted on the…

Q: Determine the addendum for each gear wheel and the contact ratio if the line of contact on each side…

A: Given: t=20 T=40 m=12 pressure angle=22.5 To determine: addendum of each gear contact ratio

Q: spur gear has a pitch diameter, Pd of 3. Calculate its Addendum

A: Since diameteral pitch is reciprocal of module. So module = 1/pitch diameter m = 1/3 m = 0.33

Q: Compute the circular pitch of a pair of gears having a ratio of 4 and a center distance of 10.23 in.…

Q: ind Spaed of Gear F ?

Q: A gearbox is needed an exact 30:1 increase in speed while minimizing overall gearbox size. input and…

A: The gear ratio is defined as it is the ratio of number of driver gear rotations to the number of…

Q: spur gear has a pitch diameter 3. Calculate its clearance

Q: Two spur gears have a velocity ratio of 0.5 The driven gear has 60 teeth of 5 mm module and rotates…

A: Data given- Velocity ratio = 0.5 T2 = 60 N2 = 200 rpm m = 5 mm

Q: 3. An involute gear of 16 teeth drives another 26 teeth gear. The diametral pitch is 3 and the…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: A set of gears is cut with a 4'½-in/tooth circular pitch and a 17/° pressure angle.* The pinion has…

Q: The circular pitch of the gear is

A: Given; Pitch circle diameter= D No. of teeth= TDetermine the circular pitch of the gear ?

Q: 6.In spur gear: a) Increasing the pressure angle increases contact ratio b) Reducing the pressure…

A: Solution:

Q: spur gear has a pitch diameter 3. Calculate its dedendum

Q: 2. Compute module, clearance, backlash and whole depth for 20° involute gears allowed for meshing…

A: Given Diametrical pitch = 20 Number of teeth = 25 To find Module Clearance Backlash Whole depth

Q: Two mating 20°, 8-pitch, spur gears have 14 and 42 teeth. Will they interfere?

A: Given Data: The pressure angle is, ϕ=20°. The pitch of the gears is, p=8. The teeth on pinion is,…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

SYSTEM AND CONTROL (MECHANICAL) (SA2)
Gear B and C are mounted on a central shaft and they rotate at the same
speed/as a unit. Gear A is the driver and gear D is driven.
Driver Gear (10 Teeth)
Driven Gear (50 Teeth)
Queshions
If gear A rotates in a clockwise direction, to which direction will gear C
rotates?
1
(2)
.2 If gear B rotates in an anti-clockwise direction, to which direction will
gear C rotates
(2)
3
Calculate the gear ration of the system
(6)
.4
Draw the systems diagram of the above mechanism
(6)
[16]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Technician A says that if a single idler gear is used to obtain reverse gear, its size and number of teeth must be used to calculate gear ratios. Technician B says that an idler gear is often used for reverse gear because it causes the output shaft to rotate in the reverse direction of the input shaft. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
An epicyclic gear train has 3 shafts A,B and CA is an input shaft running at 100 rpm clockwise. B is an output shaft running at 250 rpm clockwise. Torque on A is 50 kNm (clockwise). C is a fixed shaft. The torque to fix C
Number of Teeth on Gears A, B, C, D, E and F are 40, 132, 50, 120, 50 and 116 respectively. Gear A rotates Clockwise and is connected to a motor spinning at 900 RPM. What is the RPM and rotational direction (Clockwise/Anticlockwise) of various gears, and the final output RPM and rotation direction on shaft of gear F? What is the overall speed reduction of the drive train?
For the gear train below, th numbers of teeth for individual gears are 12 9gear #1), Gear 18 (gear #2), 14 (gear #3), and 18(gear #4), To obtain a counter-clockwise rotation of 1500 rpm for the output gear(#4). What should be the rotation speed of the input gear (#1) and in which directions should the input gear rotate
Which type of gear is more likely to develop gear whine at higher speeds? a. rotates in the same direction as the driving gear b. rotates in the opposite direction of the driving gear c. remains stationary
State two advantages of a compound gear train over a simple gear train
A system of 5 gears (gear A, B, C, D, E) with the number of teeth 20, 25, 35, 26 and 34, respectively. Gear A has a rotational speed of 600 rpm counterclockwise. a) Determine the direction and magnitude of the rotational speed for each gear (gear B, C, D, E) b) Determine the transmission number (speed ratio)
Q#2: For the two-gear system shown in following figure; a) Calculate Gear Ratio b) If the speed of Driver Gear is 30 revolutions per minute (rpm) then what will be speed of Driven Gear? c) Among two gears (driven gear and driver gear), which gear has highest speed in revolutions per minute.? d) What should be number of teeth on Driven gear to move with speed of 4 times than that of Driver Gear?
The following data relate to two meshing gears: Velocity ratio =1:3;Module: 4mm; Pressure Angle: 20°; Center distance: 200 mm Determine the number of teeth and the base circle radius of the gear wheel.
Q#2: For the two-gear system shown in following figure; a) Calculate Gear Ratio b) If the speed of Driver Gear is 30 revolutions per minute (rpm) then what will be speed of Driven Gear? c) Among two gears (driven gear and driver gear), which gear has highest speed in revolutions per minute.? d) What should be number of teeth on Driven gear to move with speed of 4 times than that of Driver Gear? (Hint: If your ID is 114-2020, then compression force would be 114 N)
A gear box conta8he 3 sizes of gears, 8 tooth, 32 tooth and 64 teeth. What is the gear ratio when the 8 tooth gear drives the 64 tooth gear?
A two-step power transmission with two identical gear sets (pinions and output gears) is designed to carry 30 HP, has an input speed of 900 RPM, and an output speed of 100 RPM. What is the speed of the middle shaft? O 750 RPM O 600 RPM O 500 RPM 0 450 RPM O 300 RPM