RLine jXLine L |L2 L V(rms) Three loads are supplied through a line in the figure. Find the magnitude of the impedance that is equivalent to the three parallel loads for the parameters given below L1 : Absorbs an average power of 20kW at a unity power factor. L2 : Absorbs an apparent power of 16 kVA at a lagging power factor of 0.9. L3 : Absorbs an average power of 10 kW and delivers 8 kvars. RLine = 0.1 X Line = 0.2 V = 25040°V (rms) Lotfen birini seçin: a.3.2565 b.3.9875 c2.1025 d2.5478 e.0.5896 f.4.6545 956878 h.1.4073

RLine jXLine L |L2 L V(rms) Three loads are supplied through a line in the figure. Find the magnitude of the impedance that is equivalent to the three parallel loads for the parameters given below L1 : Absorbs an average power of 20kW at a unity power factor. L2 : Absorbs an apparent power of 16 kVA at a lagging power factor of 0.9. L3 : Absorbs an average power of 10 kW and delivers 8 kvars. RLine = 0.1 X Line = 0.2 V = 25040°V (rms) Lotfen birini seçin: a.3.2565 b.3.9875 c2.1025 d2.5478 e.0.5896 f.4.6545 956878 h.1.4073

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.30MCQ: Under balanced operating conditions, consider the three-phase complex power delivered by the...

See similar textbooks

Similar questions

Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
Consider a load impedance of Z=jwL connected to a voltage and V let the current drawn be I. (a) Develop an expression for the reactive power Q in terms of ,L, and I, from complex power considerations. (b) Let the instantaneous current be i(t)=2Icos(t+). Obtain an expression for the instantaneous power p(t) into L, and then express it in terms of Q. (c) Comment on the average real power P supplied to the inductor and the instantaneous power supplied.
Under balanced operating conditions, consider the 3-phase complex power delivered by the 3-phase source to the 3-phase load. Match the following expressions, those on the left to those on the right. 0) Real power, Py (ii) Reactive power, Qu (ii) Total apparent power Sy (iv) Complex power, Sy (a) (V3 VLL. IL)VA (b) (V3 Vu sng) var (e) (V3 VLL. IL cos ø) W (d) Py +Qy Note that VLL is the rms line-to-line voltage, IL is the ms line current, and o is the power-factor angle.
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the average powers delivered to the load and absorbed by the line. The average powers delivered to the load and absorbed by the line are ________ and ____________ , respectively.
Suppose the circuit shown represents a residential distribution circuit in which the impedances of the service conductors are negligible and Vg1=Vg2=120 0° V (rms). The three loads in the circuit are L1 (a new refrigerator, a coffee maker, and a microwave oven); L2 (2 incandescent lamps, a humidifier, and a ceiling fan); and L3 (a clothes washer and a clothes dryer). Assume that all of these appliances are in operation at the same time. The service conductors are protected with 20 A circuit breakers. Will the service to this residence beinterrupted? Why or why not?
1. Solve for the equivalent impedance and admittance seen at the source. Solve for is(t). 2. A load Z draws 12 kVA at a power factor of 0.856 lagging from a 120-Vrms sinusoidal source. Calculate: (a) the average and reactive powers delivered to the load, and (b) the peak current.
A Y-connected balanced three-phase source is feeding a balanced three-phase load. The voltage and current of the source coil are: Calculate the following: The rms phase voltage. The rms line-to-line voltage. The rms current in the source. The rms current in the transmission line. The frequency of the supply. The power factor at the source side, state leading or lagging. The three-phase real power delivered to the load. The three-phase reactive power delivered to the load. If the load is connected in delta configuration, calculate the load impedance.
Two balanced loads are connected to a 240-kV rms 50-Hz line. Load 1 draws 30 kW at a power factor of 0.6 lagging, while load 2 draws 45 kVAr at a power factor of 0.8 lagging. Assuming the RYB sequence, determine: (a) the complex, real, and reactive powers absorbed by the combined load, (b) the line currents, and (c) the kVAr rating of the three capacitors ∆-connected in parallel with the load that will raise the power factor to 0.9 lagging and the capacitance of each capacitor. Verify the results by creating a MATLAB Simulink model and program. Obtain the plots for the currents and voltages
1. a) Find the rms magnitude and the phase angle of ICA in the circuit shown. 2. b) What percent of the average power delivered by the three-phase source is dissipated in the three-phase load?
The circuit with 3 parallel loads is described as follows. The load draws an average power of 1.8 kW (absorbing) and is behindlagging power factor 0.8. The load 2 draws 20 kVA and the leading power factor is 0.6. If the load is 3;3 Z j is an impedance of '2.5 5.0'. If the source frequency is 60 Hz, derive the steady-state equation for () V t s.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What are the RMS line current at load 1 and 2 respectively?
A 3-phase Y-connected load draws power from a 3-phase Y-connected source. The source voltage, ?=440∠0º?_rms and the load impedance, Z_y=(30+j15) Ω. The line impedance, Z_line= (1+j1)Ω and the system operates at 60 Hz. a) Draw the single-phase equivalent circuit and label all given quantities numerically. b) Calculatethe rms line (phase) current phasor in each phase. c) Calculate the total active or real power supplied by the source. d) Calculate the total active or real power consumed by the load. e) Calculate the total line loss i.e. the total activepower lost due to line. f) Determine the power efficiency of the system.