Rods ABC and CDE have been welded at point C as shown in Figure Q1 (c). Both rods ABC and CDE are supported by cables at B and D respectively. At point A, the rod ABC is supported using a rough surface. Block M3 is attached using cable at E. Taking into consideration of Newton's third law, draw the Free Body Diagram (FBD) for the rod ABC and CDE Z* M₂ B CG M₁ F CG M3

Rods ABC and CDE have been welded at point C as shown in Figure Q1 (c). Both rods ABC and CDE are supported by cables at B and D respectively. At point A, the rod ABC is supported using a rough surface. Block M3 is attached using cable at E. Taking into consideration of Newton's third law, draw the Free Body Diagram (FBD) for the rod ABC and CDE Z* M₂ B CG M₁ F CG M3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 3/4-in. horizontal steel bar loaded at constant tension and welded to a vertical support is shown in the figure. Determine the force F if the weld is E6013
A circular tube of outer diameter d3= 70 mm and inner diameter d2= 60 mm is welded at the right-hand end to a fixed plate and at the left-hand end to a rigid end plate (see figure). A solid, circular bar with a diameter of d1= 40 mm is inside of, and concentric with, the tube. The bar passes through a hole in the fixed plate and is welded to the rigid end plate. The bar is 1.0 m long and the tube is half as long as the bar. A torque T = 1000 N · m acts at end A of the bar. Also, both the bar and tube arc made of an aluminum alloy with a shear modulus of elasticity G = 27 G Pa. a. Determine the maximum shear stresses in both the bar and tube.Determine the angle of twist (in degrees) at end A of the bar.
An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than 0.22 in. when the tension in the rod is 2100 lb. If the diameter of the rod is 0.372 in., determine the maximum length of the rod.
In the figure shown, the cutaway view shows a solid aluminum alloy of L= 600mm, A= 707mm^2 and E= 70GPa rod within a closed-end bronze of L= 610mm, A= 1206mm^2 and E= 100GPa tube. Before the load P is applied, there is a clearance of 2mm between the rod flange at B and the tube closure at A. After load P is applied, the solid aluminum alloy rod stretches enough so that flange B contacts the closed end of the tube at A. If the load applied to the lower end of the aluminum rod is P= 345KN, calculate:A. The normal stress in bronze tube, in MPa.B. The elongation of bronze tube, in mm.
The figure below shows a set of plates joined by a rivet, subjected to a force F of 22.5 kN. Considering that the rivet to be used must be able to withstand a shear stress of 100 MPa, and adopting a safety factor equal to 2, what is the smallest possible diameter of the rivet?
All-round fillet weld with a steel beam weld thickness a=6 mm and weld seam length shown in the figure welded to the steel column. Forces of 2 kN and 3 kN from the beam end in the horizontal and vertical directions, respectively has been applied. The smallest yield strength of the weld material so that the steel structure has a safety of 2.5. Calculate according to von Mises static damage theory ?
A light standard for a highway is shown in figure 6.52. Although it is made entirely of welded aluminum, the member ABC is presumed to be continuous and pin connected at B and C. According to this conservative assumption, what is the tension force in the strut at B? Neglect the weight of the aluminum members.
A vertical post AB is embedded in a concrete foundation and held at the top bytwo cables as shown in Figure Q3. The post is a hollow steel tube with Modulusof Elasticity of 200 GPa, outer diameter of 40 mm, and thickness 5 mm. Thecables are tightened equally by unbuckles. -State the type of joining for Rod AB- Determine the load allowable for rod AB if a factor of safety of 3.0.- Based on the Euler buckling in the plane of the figure is desired, analysesthe requirement the maximum allowable tensile force Tallow in thecables.
An industrial machine requires a solid, round piston connecting rod 200 mm long, between pin ends that is subjected to a maximum compression force of 80,000 N. Using a factor of safety of 2.5, what diameter is required if aluminum is used with properties Sy = 496 MPa and E = 71 GPa.
Figure below shows a bolted and doweled joint eccentrically loaded in shear. The bolts and dowel pins are used to connect the two parts. The shear loads are taken by the dowel pins, the sizes of which are: dA = 0.375 in, dB = 0.375 in, dC = 0.250 in, dD = 0.250 in, dE = 0.250 in. Dowels with diameters of zero are not present. Though the figure shows 5 dowel pins, that is not the case if some dowels are with zero diameters. Assume that a = 4 in, b = 4 in, l = 10 in, P = 2500 lb. Suppose that all of the dowels will take all the shear loading and will share the load equally. Assume that one part is allowed to rotate slightly about the centroid with respect to the other part. Part A Find the magnitude of the total shear force acting on dowel A. Express your answer in pounds to three significant figures. Part B Find the direction angle of the total shear force acting on dowel A measured counterclockwise from the positive x axis. Express your answer in degrees to three…
Draw the free-body diagram for the following problem. The rod shown.
The AB bond must be made of a steel for which the normal stress limit is 450 MPa. Determine the cross-sectional area for AB for the which the safety factor is 3.50. Suppose the link is adequately reinforced around the pins at A and B. What is the deformationof bar AB when subjected to the load applied to it considering the modulus of elasticity of steel E = 210 Gpa and the length L of thebar equal to 0.75m (All dimensions are in meters)?