i need the answer quickly hardness testRokolpernell with aload of 3000kg andVickersa ball with a diameter of 10mmpyramid of Rokol C coneRokol B ball and Rokol A conehardnessimpactdiamondsand 150 kg100kg| and 60 kgnumberdiameter64057.379.82.50...53351.376.54952.7544044.572.84153.0037237.969.33523.2531932.166.33023.50...27626.663.62623.7524120.560.82294.00...20293.058.02024.25...17988.056.01794.5015983.053.01594.75...14378.01435.00...12671.01285.2511665.01165.509858.01055.75Hardness numbers in different ways: Brinell, Rocol and Vickers

Answered: Image /qna-images/answer/5b03841b-068d-42ea-9e7c-56c53c0e9a38.jpg

Answered: Rokol pernell with aload of 3000kg a…

Rokol pernell with aload of 3000kg a 'ickers a ball with a diameter of 10n ramid of Rokol C cone Rokol B ball and Rokol A cone hardness impact amonds and 150 kg 100kg and 60 kg number diameter

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In inserting an aluminum piston into a steel cylinder, it is given that the inside diameters of the cylinder and of the piston are 0.500 m and 0.4998 m, respectively, at 25OC. The temperature to which they are heated to obtain a perfect fit is 55.8 degrees celsius. Show the solution.
A mild steel material is subjected to a Brinell hardness test with an applied force of 8145 N using a hardened steel ball indentor of 10 mm and it is found that the Brinell Hardness Number as 966. Determine the surface area of indentation and indentation diameter
A 2-cm square cross-section steel part having a Brinell hardness of 200 and a length of 5 cm is to be ground by adhesive wear using a tool of electroplated chromium with a square head of 2 mm x 2 mm. If the normal force applied is 20 kN and the depth to be removed from the surface is 4 mm, determine the number of passes needed (parallel to the length direction) for poor lubrication. Select one: O a. N = 1570 O b. N = 2093 O c.N = 6278 O d. N = 3139
4 In hardness test, a force of 3000 kgf applied using steel ball of 10 mm, the result hardness value is (BHN=200+N) where N is your number in class. Calculate the mean depression w bli nöy :diameters (d)? N=92
14. A commonly used method of fastening one part to another part iscalled “shrink fi tting.” A steel rod has a diameter of 2.0026 cm, and afl at plate contains a hole whose diameter is 2.0000 cm. The rod is cooledso that it just fi ts into the hole. When the rod warms up, the enormousthermal stress exerted by the plate holds the rod securely to the plate. Byhow many Celsius degrees should the rod be cooled?
The S-N curve which represents the fatigue strength, which is measured as a stress amplitude, as a function of number of stress cycles, can be approximated by a straight line in therange of 103cycles to 106cycles when plotted as log(S) versus log(N). Beyond 106cycles,the fatigue strength remains constant. The fatigue strength of a certain alloy at 103cyclesis given as 80 % of the ultimate tensile strength and its endurance limit is 50 % of theultimate tensile strength.(a) The alloy part fails in 15 000 cycles. Calculate the percent change (increase or decrease)of the maximum applied cyclic stress amplitude if the life of the part needs to beextended by 3.5 times. Is this considered under a high or low cycle fatigue failure?State any assumptions made. (12 marks)(b) If the applied cyclic stress amplitude remains unchanged when the life is extended by3.5 times, calculate the percent change (increase or decrease) of the ultimate tensilestrength of a new alloy required. (8 marks)(c) If the…
Determine the indentation diameter and the surface area of indentation of a copper material subjected to a Brinell hardness test with a test force of 7.3 kN using a hardened steel ball indentor of 11 mm. Take the Brinell Hardness Number as 948. Solution: i) Indentation Diameter (in mm) = ii) Surface Area of Indentation (in mm2) =
A cylinder speamen 380 mm bital length. If the load force of 6660N with Madual of Elashicly 110gpa and elongadium of 0.5mm then determine the diameter of test cylinder ?
PLSS ANSWER ASAPPP Which is correct about spherical shell? a It has the same formula as hoop stress b The wall of the pressurized spherical vessel is subjected to uniform comporessive stress in all directions c It has the same formula as the tangential stress d The wall of the pressurized spherical vessel is subjected to uniform tensile stress in all directions
From the work of D. C. Jillson, Trans. AIME 188, 1129 (1950), the following data were taken relating to the deformation of zinc single crystals. The crystals have a normal cross-sectional area of 122 x 10-6 m2. ϕ = angle between loading axis and normal to slip plane λ = angle between loading axis and slip direction F = force acting on crystal when yielding begins a. Identify the slip system for this material. b. Calculate the resolved shear τRSS and normal σn stresses acting onthe slip plane when yielding begins. c. From your calculations, does τRSS or σn control yielding? d. Plot the Schmid factor versus the normal stress P/ A0 acting on the rod. At what Schmid factor value are these experimentally-measured yield loads at a minimum? Does this make sense?
Determine the young’s modulus value of each material testing, and indicate which material is the shaft made from. Use the experimental data provided from the torsion test conducted on the shafts from three different materials. The materials included in this test are Aluminium, Brass, and Steel. Ensure you work through the provided tables and indicate which results correspond to which material. Dimensions Diameter (mm) 6 Length (mm) 77 J= (π ×D^4)/32 G= TL/θJ Degree Radian Material 1 Material 2 Material 3 1 0.017453 1.11 1.83 0.47 1.5 0.02618 1.47 2.46 0.76 2 0.034907 1.84 3.2 1.01 2.5 0.043633 2.72 3.93 1.32 3 0.05236 2.7 4.72 1.65 3.5 0.061087 3.11 5.54 1.99 4 0.069813 3.36 6.4 2.32 4.5 0.07854 3.98 7.27 2.66 5 0.087267 4.41 8.18 3 5.5 0.095993 4.84 9.15…
The rotation in degrees of a shaft, 800 mm long subjected to atorque of 80 N-m, 10 mm in radius and shear modulus of 85 GPais