ROLLER GATE WATER SURFACE R=4 m WATER SURFACE c 307 6.0 m 30 HÍNGE DAM Fig. 3.60 Fig. 3.59 21. Find the horizontal and vertical components of the water pressure exerted on a tainter gate of radius 4 m shown in Fig. 3.60. Consider width of the gate unity. (Problem 3.25)

ROLLER GATE WATER SURFACE R=4 m WATER SURFACE c 307 6.0 m 30 HÍNGE DAM Fig. 3.60 Fig. 3.59 21. Find the horizontal and vertical components of the water pressure exerted on a tainter gate of radius 4 m shown in Fig. 3.60. Consider width of the gate unity. (Problem 3.25)

Name: ROLLERGATEWATER SURFACER=4 mWATER SURFACE C.3076.0 m30-HÍNGEDAMFig. 3
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: ROLLERGATEWATER SURFACER=4 mWATER SURFACE C.3076.0 m30-HÍNGEDAMFig. 3.60Fig. 3.5921. Find the horizontal and vertical components of the water pressure exerted on a tainter gate of radius4 m shown in Fig. 3.60. Consider width of the gate unity. (Prob

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In Fig., gate AB is 5 ft wide into the paper, and stopB will break if the water force on it equals 9200 lbf. Forwhat water depth h is this condition reached?
A dam with triangular cross section holds back a body of water. The dam has height h. The dam is made of concrete, which has speci…c gravity 3.1. What is the maximum angle, , for which thedam will not tip over about point O?
An open vessel of water accelerates up to a 30ᵒ plane at 2 m/s². a). What is the angle the water surface makes with the horizontal? B). If the angle mage by the water surface to the horizontal is increased to 25.21ᵒ, what will be the depth of water at the rear side of the vessel, if the initial depth of water at the rear side is 4m and the front is 2m before accelerating? The vessel has a length of 4m and 2m width. C). If the vessel’s depth at the rear side is 5m, what will be the volume spilled if the acceleration is increased to 15m/s²?
Figure AB Cover rests on a flat surface. Cover 180 kg weight and 1.2 m wide. At what height is the water depth the lid won't open? find it. (glycerin density is 1260 kg/m3 , That density 1000 kg/m3 )
A triangular gate having horizontal base of 1.0m and an altitude of 1.5m is inclined 45° from the vertical with the vertex pointing upward. The vertex of the gate is 2.4m vertically below the surface of the water. What normal force , in KN, must be applied at the vertex of the gate to open it's hinged at the base?
A gate rotates at point A and releases water when the water's depth, d, exceeds a certain value. The gate's width (perpendicular to the image) is b = 2.95 ft, the water's depth is d = 4.82 ft, and point A is located at h = 2.41 ft. a) What is F, the magnitude of the horizontal force exerted on the gate by the water? The water's specific weight is γw=62.4lb/ft3. b) What are Ax and Bx, the horizontal reaction forces at points A and B that act on the gate from Part A. c) What is dmax, the water's maximum depth before the pressure causes the gate from part A to open?
A hollow circular plate of 3 m external diameter and 1 m internal diameter is immersed in water such that its centre is at a depth of 2.5 m from the water surface. Find the total pressure and the point where it acts.
A closed cylindrical vessel, 2m in diameter & 4m high is fully filled with water & rotated to its vertical axis at a constant speed of 12.2 rad/sec. The top is pressurized by 180 KPa. (a) What is the pressure at the center bottom of the cylinder? (b) What is the pressure at the circumference bottom of the cylinder? (c) What is the total hydrostatic force at the sides of the cylinder?
A cubical block of wood 13 cm on an edge weighing 20 N floats in water (9810 N/ cubic meter). If it is depressed so that its upper face lies in the water surface and is released, find the equation of the motion. Neglect resistance
Hydrostatic: A 2-m-wide, 3-m-high vertical rectangular gate has its top edge 2 m below the water level. It is hinged along its lower edge. What force, acting on the top edge, is necessary to hold the gate shut?
A wedge splits a sheet of 20 °C water, as shown in Fig.P3.39. Both wedge and sheet are very long into the paper.If the force required to hold the wedge stationary is F =124 N per meter of depth into the paper, what is the angleθ of the wedge?
A hollow circular plate of 2 m external and 1 m internal diameter is immersed vertically in water such that the centre of plate is 4 m deep from water surface. Find the total pressure and depth of centre of pressure.