S-1) Given in Figure 1; a) Find the dimensions d, b and c? b) Calculate the stresses occurring in the aluminum square pipe and the inner steel and indicate whether the section withstands these stresses? o, steel = 170 N/mm2, o. aluminum = 60 N/mm2)

S-1) Given in Figure 1; a) Find the dimensions d, b and c? b) Calculate the stresses occurring in the aluminum square pipe and the inner steel and indicate whether the section withstands these stresses? o, steel = 170 N/mm2, o. aluminum = 60 N/mm2)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The five-bolt connection shown in the figure must support an applied load of P = 295 kN. If the…

Q: The lap joint is fastened with four 0.52-in-diameter rivets. The working stress is 19.7 ksi for the…

A: Given Data The diameter of the rivet is: d=0.52 in The working stress is: σw=19.7 ksi=19700 psi The…

Q: Q2 Find the stress in steel bar

A: P = 10 KN Diameter = 14 mm = 0.014 m

Q: The 175x100x16mm angle shown in the figure connected to a gusset plate with three 25mm dia. bolts…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: shear yield stress of the

A: Given; Uniaxial yield stress of a material is ,σy=280 MPa Find shear yield stress of the material,…

Q: 2- What is the maximum shear stress in the shaft in (MPa)?

Q: The lap joint is fastened with four 0.87-in.-diameter rivets. The working stress is 12.34 ksi for…

Q: -n with = cost +

A: The equation for simple harmonic motion(free motion) is m d2xd t2 + kx=0 ( drag force is negligible)…

Q: 2 -1 o =|-1 2 1 -1 2 -1 Find (a) Principal stress (b) Principal directions (c) Invariant

A: TO FIND: (a) Principal stress (b)principal direction (c) Invariants GIVEN: stress tensor:…

Q: A flanged bolt coupling is used to connect a solid shaft 86 mm in diameter to a hollow shaft 100 mm…

A: INTRODUCTION : Flange coupling is the process of joining two shafts or tube ends in a flush, sealed…

Q: 125 mm 175 mm D -225 mm- 75 mm 150 N Fig.3

A: Answer: (a) The tension in cable ABD is 195 N. (b) The reaction at support C is 216.33 N at an angle…

Q: rectangular section the ratio of maximum shear stress to the average shear For a stress is

A: Given data : Rectangular section Width=B Depth=D Shear force=V Average shear stress=ζAvg Maximum…

Q: Q: A block is 45 mm long, 20 mm high, 10 mm thickness. the block is subjected to a uniformly…

Q: The wooden members A and B are to be joined by plywood splice plates that will be fully glued on the…

A: Given data as per the question P = 33.6 kN L = 361 mm W = 151 mm there are four separate areas…

Q: 34. Stress is given by the following formula: (choose correct sentences) a. 8 = 4 b. 8 == c. 8=Ex=…

A: Find Stress is defined as. Types of Cast Iron

Q: Required information Consider the given state of plane strain. Ex=-180µ, Ey=-260µ, Yxy=+295µ Use…

A: By the Mohr's Circle as shown below

Q: A hole is to be punched out of a plate having a shearing strength of 40 ksi. The compressive stress…

Q: 3- Calculate the number of finished goods (output) or N for the figure illustrated below:

A: Given: Total number of goods xi = 1200 Goods accepted after casting = 90% = 0.9 Goods sent for…

Q: The lap joint is fastened with four 0.65-in.-diameter rivets. The working stress is 20.72 ksi for…

Q: 1. Use the diagram below to answer the following questions a. Determine the normal stress exerted on…

Q: Required information Consider the given state of plane strain. Ex =-180µ, Ey=-260µ, Yxy= +295µ Use…

A: Since you have asked multiple questions, only the first question is solved for you. If you want any…

Q: The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the…

Q: 1 kN load is applied to the plates in shear, what is

Q: What is the max shear stress on a shaft under a torque of T = 54.167 lb-ft having a diameter of 0.75…

A: When a shaft is subjected to torque, shear stress produces in the shaft. The torsion equation is…

Q: The steel wide-flange beam has the dimensions shown. If it is made of an elastic perfectly plastic…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: 12 MPa MPa 15 MPa For the given state of stress. The orientation of the planes of maximum in-plane…

A: Write the given data with suitable variables. σx=4 MPaσy=12 MPaζxy=15 MPa

Q: Shear force is unbalanced to the left or right of the section.

A: The shear force of a beam may also be defined as the unbalanced vertical force to the left or right…

Q: In a beam, the positive shear in the left end is pointed __________________. Group of answer…

A: Let suppose a beam of L length. Load P is pointed at the end of beam

Q: A beam is loaded as shown in the figure. F = 2000 Ib, b = 3 in. and h = 6 in. F 3 ft 9 ft b h 12 ft…

A: Answer: (a) The maximum shear force in the beam is 1500 lb. (b) The maximum bending stress in the…

Q: 2. A figure shows a state of stress; determine the shearing stresses and normal stresses after the…

A: Given data σx=8 ksiσy=-12 ksiτxy=6 ksi Here, σ represents the normal stress and τ is the shear…

Q: Please simply sketch the shear stress diagram 0.5 in. 0.6 in. 0.d in. / 0.8 in. 0.2 in. 0.6 in. ||B

A: GIVEN: To Sketch the Shear Stress Diagram.

Q: Calculate the stress in the steel from the given figure. Use P1=300KN and P2-45KN. Answer in MPa…

Q: A flanged bolt coupling is used to connect a solid shaft 85 mm in diameter to a hollow shaft 100 mm…

Q: Draw the Mohr's Circle (Fig. 3) as accurately as possible on a graph paper. (a) Using equation find…

Q: B=56 inside diameter = 66 in. wall thickness=0.23 in. allowable normal stress perpendicular to the…

Q: in the figure, the vertical shear is 45 etermine the shearing stress of poir

Q: A machinist wishes to insert a brass rod with a diameter of 3 mm into a hole with a diameter of…

Q: Mr. Jae Yeong wants to put up a plant rack for his mini garden using a recyclable material from…

Q: What is the Shear Force,V?

A: To define: The shear force. Concept used: Shear force: Shear force is an internal force in any…

Q: 1: Choose the correct answer from the following:- 1. The relationship between maximum shear stress…

Q: 2- Give the approximate position of the centroid for each cross-sections with respect to the…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 5) The kind of stress in flange portion of a partially drawn cylindrical cup when deep drawing…

A: Deep drawing is one of the most common processes for sheet metal processing. It is the process in…

Q: A figure shows a state of stress; determine the shearing stresses and normal stresses after the…

Q: Oy Ot Txy Tnt Ox On n (b) (a) On the surface of a structural member, stresses are given as ox=67,9…

A: The stress stress after rotation is given by - τnt=-σx-σy2sin2α + τxycos2α In first case-…

Q: Question 4 n punching a hole on a metal plate, the puncher exhibits shearing stress. O True F) False

A: True , puncher exhibits shearing stress, shear stress is responsible for punching out of hole.

Q: In Figure 4.1, assume that a 21 mm diameter rivet joins the plates that are each 110 mm wide. The…

Q: find the principal stress , maximum in plane shear stress

Q: (a) The plane stress at a point with respect to x-y-axes is shown in Fig. Q1(a). By using…

A: according to the given details:

Q: 5. Distinguish clearly between direc stress and bending stress

A: Stress induced in the body due to tension or compression is called Direct Stress. For example, when…

Question

S-1) Given in Figure 1; a) Find the dimensions d, b and c?
b) Calculate the stresses occurring in the aluminum square pipe
and the inner steel and indicate whether the section withstands
these stresses?
o, steel = 170 N/mm2,
o. aluminum = 60 N/mm2)
6.a kN
a= 17.7
6.a mm
steel
0,5mm
aluminum
90.a
Çelik
6.al
8.a mm-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

why do you multiply by 16 in the shear stress?
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER 1. Using MOHR CIRCLE from the given stresses on two perpendicular planes what is the normal stress on plane a-a? a. 75 MPa b. 150 MPa c. 125 MPa d. 100 MPa 2. Using MOHR CIRCLE, what is the resulting "HORIZONTAL" SHEARING STRESS at the given angle plane point? a. 44.03 MPa b. 64.32 MPa c. 185.68 MPa d. 75.00 MPa 3. Using MOHR CIRCLE, what is the resulting "VERTICAL" NORMAL STRESS at the given angle plane point? a. 44.03 MPa b. 75.00 MPa c. 64.32 MPa d. 185.68 MPa
The drive shaft for a truck (outer diameter 60 mm and inner diameter 40 mm) is running at 42 Hz. If the shaft transmits 133 kW, what is the maximum shear stress in the shaft in MPa? Round up final answer to whole number
What is the Absolute Maximum Shear Stress?
Choose correct answer: Maximum stress on a principle plane is Tangential stress shear stress Normal Stress Resultant stress
The allowable stresses for the splice shown are the following: 150 MPa for shear of rivets, 1.35Fy for bearing,0.60Fy for tension and Fy = 250 MPa. Note: rivet holes are 2 mm bigger than the rivet diameter and the middleplate is 20 mm thick. Find the diameter of the rivets so that the joint capacity due to shear approximately equal to the bearingcapacity.a. 25.4 mm c. 28.65 mmb. 30.79 mm d. 36.97 mm Find the maximum safe value of P without exceeding the allowable shearing stressa. 773.6 kN c. 938.3 kNb. 878.1 kN d. 848.2 kN Find the maximum safe value of P without exceeding the allowable tensile stress.a. 579.3 kN c. 716.1 kNb. 495.5 kN d. 692.5 kN
Fast. A machine part is subjected to an axial loading situation where Fmin = 3700 lbf and Fmax = 12000 lbf. The cross-section area at the critical location is 1.6 in2. Assume Kf = 1. Determine the alternating stress in units of ksi, with one decimal place.
4 In hardness test, a force of 3000 kgf applied using steel ball of 10 mm, the result hardness value is (BHN=200+N) where N is your number in class. Calculate the mean depression w bli nöy :diameters (d)? N=92
What is the Shear Stress Distribution?
Please answer the problem completely. Show a free body diagram. Final answer: Shear stress = 3.2 mpa
Choose the stress to which the size correction factor should be applied in Soderberg's formula. a. Mean stress b. Yield stress c. Variable stress d. Endurance limit stress Clear my choice
can you resolve the problem but with 10mm diameter, l=100mm, P=7850N, change in diameter = 3.25x10^-3mm