secondary cell having an e.m.f. of 2V and an internal resistance of 1 ohm is connected in series with a primary cell having an e.m.f. of 1.5V and an internal resistance of 100 ohm. The negative terminal of each cell is connected to the positive terminal of the other cell. A voltmeter having a resistance of 50 ohm is connected to measure the terminal voltage of the cells. Calculate the voltmeter reading and the current in each cell.

secondary cell having an e.m.f. of 2V and an internal resistance of 1 ohm is connected in series with a primary cell having an e.m.f. of 1.5V and an internal resistance of 100 ohm. The negative terminal of each cell is connected to the positive terminal of the other cell. A voltmeter having a resistance of 50 ohm is connected to measure the terminal voltage of the cells. Calculate the voltmeter reading and the current in each cell.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

How would u measure the amperage across a resistor with a multi-meter?a) Connect the multi-meter in series with the resistorb) Connect the multi-meter in parallel with the resistorc) Connect the multi-meter in parallel with the sourced) Any of the above would work
In the figure is shown a battery having an emf of 12 Volts and an internal resistance of 0.40 Ohm.A resistor R1 of 2.6 Ohms is connected across itsterminals ab. Determine (a) resistance of Rwhich, when connected across terminals ab inparallel with R1 will make the powerdelivered by the battery a maximum; (b)current in R1 and R; (c) terminal voltage ofbattery; (d) power in R1 and in R; (e) power lost in batteryHint: To maximize power in R, use differentiation In the circuit shown, a 6-Ohm resistor connected in series to a parallel combination of tworesistors, one is 30-Ohm and the other is R beingunknown. Determine the value of R if: (a) thepower dissipated in 6-Ohm resistor is equal tothe power in the parallel combination; (b) hepower in 6-Ohm is equal to the power of in R; (c)value of R maximum power transfer.Hint: To maximize power in R, use differentiation
Determine the equivalent resistance from points b and c. use wye and delta computations and series and parallel.
shfdjkfdrhnacoioeniodinopidopdnieocmixoxwmipdf.ziudSALIDUDetu The equivalent resistance of three resistors A, B and C connected in parallel is 1.5 ohms. If A is thrice of B and C is 1/4 of B. Find the equivalent resistance when the three of them are connected in series? dhffrriru9ee
A 20-ohm resistor is connected in parallel with a variable resistor R. The parallel connection is then connected in series with a 4-ohm resistor and connected across a 240 V source. Determine the minimum value of R if the power of R is equal to the power taken by the 4-ohm resistor. *Draw a diagram before the solution
What Rx in parallel with 40 ohm will provide and Req of 24 ohm?
A 40 - Ω resistor is connected in series to a parallel combination of a 60 - Ω resistor and a 30 - Ω resistor to form a load across a 120 – volt source. Draw the closed-circuit diagram. Determine the current through and the voltage across each resistor.
A 5-ohm resistance is connected in parallel with a 10-ohm resistance. Another set, a 6-ohm and an 8-ohm resistances are also connected in parallel. The two sets are connected in series. What is the equivalent resistance?
Determine the equivalent resistance from points d and f. use wye and delta computations and series and parallel.
Using the black box from below, construct a circuit that fulfills the following objectives: Volage in point A: 500mV Voltage in point B: 1000mV
a. For the resistors in series, is there a significant difference in the values of individual currents? If there are, what are the sources of variation? b. For the resistors in parallel, is there a significant difference in the values of individual currents? If there are, what are the sources of variation?
Determine the current passing through each resistor in Figure Given. Note: The topic is all about Mesh Analysis.thank you