See the rigid L-shaped bar below ABC can pivot about the point A. CD 250 mm is a hydraulic cylinder. CD can pivot about D and connects to ABC by a pin at C. Initially, AB is horizontal, and BC is vertical. Cylinder CD 20° 300 mm extends by 100 mm (to 350 mm). Determine how the point C moves horizontally and vertically 500 mm a) specify movement of C to the right or left and by how much b) specify movement of C up or down and by how much

See the rigid L-shaped bar below ABC can pivot about the point A. CD 250 mm is a hydraulic cylinder. CD can pivot about D and connects to ABC by a pin at C. Initially, AB is horizontal, and BC is vertical. Cylinder CD 20° 300 mm extends by 100 mm (to 350 mm). Determine how the point C moves horizontally and vertically 500 mm a) specify movement of C to the right or left and by how much b) specify movement of C up or down and by how much

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

A uniform beam that 10-m long is being supported by two men, one man at each end. The weight of the beam. Is 100-N. If the first man supporting at the right side exert twice as much as the second man on the left, where must a 50-N motor be placed (measured from the first man) on top of the beam? Show complete solution.
A vertical bar of length L with mass of 40 kg is rotated vertically about its one end at 40 rpm. Find the length of the bar if it makes and angle of 45° with the vertical.
A crane that is 10 meters long is rotating (while loaded), at 1 radians/sec. It is stopped instantly (in 0.1 radian) in the position shown. Due to momentum the load continues to swing. Ignoring the deflection of the crane for this problem. (list all assumptions). The load is 750 lbs. a) The weight of the 10 m crane boom is 3000 lb and the mass moment of inertia is 80 lb ft s^2 about the centroid. Using the parallel axis theory find the mass moment of inertia around the point of rotation. b) What forces and moments are there on the boom at the point of rotation?
The compound pulley in Fig. P-1223 has a centroidal mass moment of inertiaof 20 ft-ib-sec2. Find the tension in the cord supporting the 161-Ib weight.
Consider Figure 5.28. The driver attempts to get thecar out of the mud by exerting a perpendicular force of610.0 N, and the distance she pushes in the middle of therope is 1.00 m while she stands 6.00 m away from the caron the left and 6.00 m away from the tree on the right.What is the tension T in the rope, and how do you find theanswer?
Two masses A and B are 5kg and 2kg respectively rotating in a shaft. The corresponding radii of rotation are 0.2m and 0.3m respectively and the angle between the masses is 600. Find the position and magnitude of the balance mass required, if its radius of rotation is 200 mm using graphical method and also verify your answer with analytical method.
Q. 1 The slender bar is pinned at point A and held in the horizontal position by a cable as shown in the Fig. (a). The cable is cut at (a) What is the bar’s angular velocity after it has rotated through 20°? (b) What are the reactions at the pin support after it has rotated through 20°?
A uniform ladder 8 meters long and weighing 350 N rest against a smooth vertical wall at an angle of 30 to the wall. A 700-N man stands 6 meters up from the bottom of the ladder. Find the horizontal force necessary at the base to keep the ladder from slipping Show the Figure/FBD, given and the formula used
nonuniform beam 4.50 m long and weighing 1.40 kNmakes an angle of 25.0° below the horizontal. It is held in position bya frictionless pivot at its upper right end and by a cable 3.00 m fartherdown the beam and perpendicular to it . The center ofgravity of the beam is 2.00 m down the beam from the pivot. Lightingequipment exerts a 5.00 kN downward force on the lower left end ofthe beam. Find the tension T in the cable and the horizontal and verticalcomponents of the force exerted on the beam by the pivot. Start bysketching a free-body diagram of the beam.
Find the range of values of Lo if L1= 30mm, L2=70mm and L3=100mm for a. Crank Rocker b. Drag Link c. Double Rocker d. Cross over- position e. Triple Rocker
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=250 N. The distance between the points A and B where the cables are attached to the leg is given as L=100 cm and the angle of the leg with the horizontal is γ=6°. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=40°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
Draw the free-body diagram for the following problem. The crane and boom shown.