Shaper machine uses single point cutting tool for cutting mater Select one: True False

Q: Angle between side cutting edge and axis of tool is known as: * Back rake angle Side rake angle Side…

A: Answer: The correct answer is option (c) side cutting edge angle.

Q: i. spindle rpm ii. feed speed iii. cutting time iv. material removal rate

A:

Q: The positive rake angle in a single point cutting tool is used to cut non-ferrous metals and low…

A: Positive rake angle is provided to low strength material, to reduce BUE, for low speed operation

Q: An aluminum hollow shaft 200 mm outside diameter, 100 mm inside diameter and 500 mm length from…

A: Given Data Outside diameter of shaft is : do=200 mm Inside diameter of shaft is :di=100 mm Length…

Q: 44. Bigger diameter end mill cutting tool is preferred during milling operation. Select one: True O…

A: In general, milling is a machining process in which the rotary motion of the cutter is used to…

Q: Which would you use for any of the following situations: Cutting on a smaller mill, a larger mill…

A: Given data: For cutting a smaller mill  A larger mill with little clearance A smaller diameter…

Q: In a multi point cutting tool the positive rake angle is used to cut low tensile strength and…

A:

Q: Identify the machining operation Profiling Facing Face Grooving Grooving

A:

Q: Step boring is advised to be used for: Machining hard materials O Machining large radial depth of…

A: Various types of machining operations used are: Turning Boring Drilling Step boring Counter boring…

Q: Up milling operation is performed for finishing cut. Select one: True O False

A: Down milling is performed for finishing and get smooth surface.

Q: Lathe Machine tool is an example of three axes machines

A: Lathes, by definition, are 2-axis machines. Once machines advanced to incorporate 3-axis, 4-axis…

Q: Choose TWO (2) types of cutting processes for cutting thin metal (sheet metal)

A:

Q: Tool forces are generated by the fixture or jig during a machining cycle O True False

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Identify Counter-sinking operation from the following drilling operation a. Ob. C. Work stationary O…

A:

Q: The angle on a single-point cutting tool geometry in which the face of a tool is inclined sideways…

A: Back rake angle: It is the inclination of the face toward or away from the end or the end cutting…

Q: 3. Describe the characteristic of good cutting tools

A: Good cutting tool must have the following characteristics:- Good strength High thermal stability…

Q: The following tool is used to cutting internal threads of drilled hole Select one: a. Drill plate b.…

A: It is required to which tool is used to cutting internal thread of drilled hole

Q: Up milling operation is performed for finishing cut. Select one: True False

A:

Q: Which of the following best describes the "cutting plane" of aligned sectional view: It is a…

A: it is a combination of parallel cutting planes

Q: In a multi point cutting tool the negative rake angle is used for high tensile strength materials.…

A: Positive rake angle used for ductile or soft material while negative rake angle used for higher…

Q: An aluminum hollow shaft 200 mm outside diameter, 100 mm inside diameter and 500 mm length from…

A: Given data as per question The outside diameter of shaft =200 mm Inside diameter =100 mm Length of…

Q: Up milling operation, the work is feed in the same direction the rotation of the cutter. Select one:…

A: Given :-  Up milling operation, the work is feed in the same direction the rotation of the cutter.…

Q: From the following Identify cutting tool formed by grinding the end piece of a steel stock is O a. O…

A: Option d is correct.

Q: Answer the following questions by circling True or False. 13. The cutting speed of the hydraulic…

A: As per Bartleby guideline we are allow to give answer of one question at a time so please post other…

Q: The breakeven cutting speed

A: Given data, Two cutting tools with tool life equations given below are being compared:  Tool 1:…

Q: proper Cutting and feed being ant? o we Set the tool just piece center-line h1 mm depth of cut ece…

A: 1 cutting speed and feed is very important parameters in metal removal process because a) it…

Q: Center drilling operation performed on lathe machine uses a single-point cutting tool. Select one:…

A: Answer is false

Q: Main advantage of the Forming taps is:         a/ Evacuates the chips along the shank (for blind…

A: Option b is correct.

Q: Angular Holes                  1.  Principle of drilling Angular Holes                  2.  Basic…

A: When the motor is turned on, the spindle revolves, and the stepped pulley linked to it turns as…

Q: Increasing the cutting speed (Vc) affects the surface finish by:

A: The dimensional accuracy of the final product depends on the cutting speed.

Q: 12. What must be the cutting speed of two inches milling cutter if it has to machine a piece of mild…

A:

Q: Drill bit is fixed in the tailstock of a lathe during the drilling operation. Select one: True False

A: Solution:

Q: Angle between side cutting edge and axis of tool is known as: Back rake angle O Side rake angle Side…

A: Angle between side cutting edge and axis of tool is given as Side cutting edge angle or side cutting…

Q: 10. Formula for cutting speed of the shaper, tell the meaning of each variables.

A: SHAPER In shaping, the cutting tool is held in the tool post located in the ram, which reciprocates…

Q: Define the fundamental of cutting.

A: Definition of Cutting : Cutting is defined as It's process which creates new surfaces in a solid by…

Q: Cross slide is actively used during ___________machining operation on lathe. a. Drilling b. Turning…

A: Answer: Turning

Q: A single point cutting tool designated as follows 8-14-6-6-6-20-1 is used to machine a work with…

A:

Q: Briefly describe the meaning of spark gap in wire cut machining by drawing a sketch.

A: Wire cut machining  The spark gap is the gap given between the conductors to pass an electric spark…

Q: Identify the true statement from the following a. Unit of cutting speed in millimetre per minute b.…

A: There are various terms related to the machining operations, such as cutting speed, feed rate, depth…

Q: Type of milling operation to produce flat surfaces with cutter axis perpendicular to the milled…

A: True  Explanation :-  In face milling , milling cutter is placed  is placed perpendicular to the…

Q: Excessive temperature at the cutting tool point will lead to the following: Brittle fracture ، All…

A: Excessive temperature at the cutting tool point is very dangerous.

Q: Friction less cannot be with cutting surfaces. * True O False Extrudina does not

A: 1.Friction less cannot be with cutting surfaces False When the cut surface is not flat frictionless…

Q: Angle between side cutting edge and axis of tool is known as: Rack rako anglo

A: Given:Lathe tool has so many angles and edges. All the edges has different work.

Q: Choose TWO (2) types of cutting processes that are suitable for cutting thick materials (>20mm thick…

A: 1.Plasma cutting  Plasma cutting use accelerated jet of hot plasma to cut the electric conductive…

Q: From the following Identify cutting tool that has the cutting edge in the form of small tip made of…

A: Let us discuss about about given single point cutting tool

Q: Match the Types of saws on the left column with their characters and applications on the right…

A: To match the type of saws (on the left side ) to their character and application (on the right side…

Q: Question 1. The shaping machine is used to machine flat metal surfaces especially where a large…

A:

Q: process used for cutting a gear on a milling machine is called The a. Gear forming b. Gear shaping…

A: Option c is correct

Q: The tool has only one cutting edge and the cutting edge is made of high-grade material like carbide…

A: Carbide is very hard material that is used for the purpose of the cutting tool formation.

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.