Question
Show that the volume expansion coefficient of an ideal gas is B=1/T, where T is the
absolute temperature.
Expand
Transcribed Image Text

Show that the volume expansion coefficient of an ideal gas is B=1/T, where T is the absolute temperature.

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Mechanical Engineering

Thermodynamics

Related Mechanical Engineering Q&A

Find answers to questions asked by students like you.

Q: A grist mill of the 1800s employed a waterwheel that was 14 m high; 480 L/min of water flowed onto t...

A: Given: The height of the water wheel is H=14 m. The volume flow rate of the water on the wheel is V=...

Q: Select correct answers

A: Click to see the answer

Q: Oil at 20°C is flowing through a vertical glass funnel that consists of a 20-cm-high cylindrical res...

A: Given: The diameter of pipe = 1 cm The height of cylindrical reservoir = 20 cm The height of the pip...

Q: 12-63. From experimental data, the motion of a jet plane while traveling along a runway is defined b...

A: Given: The velocity of the plane is v The acceleration of the plane is a The displacement of the pl...

Q: 17-105. If the coefficient of static friction between the 50-lb roller and the ground is u, = 0.25, ...

A: Click to see the answer

Q: Refrigerant-22 absorbs heat from a cooled space at 50°F as it flows through an evaporator of a refri...

A: Given data: *The temperature at which the refrigerant R22 absorb heat from cooled space is T1=50°F *...

Q: Use the rectangular component method to solve the fol- lowing problems. Determine the magnitude R of...

A: The forces have been resolved into its components as follows:  

Q: Refrigerant-134a is expanded isentropically from 600 kPa and 70°C at the inlet of a steady-flow turb...

A: Given Data: The inlet pressure of the refrigerant R-134a is P1 = 600 kPa. The inlet temperature of ...

Q: The dry bulb and wet bulb temperatures of a room are measured as 30C and 20C, respectively. After mo...

A: The two points are shown on the psychometric chart below. Initial point -1 Final point -2

Q: (a)The device shown in figure 5 is designed to apply pressure when bonding laminate to each side of ...

A: Click to see the answer

Q: A piston–cylinder device contains 2.2 kg of nitrogen initially at 100 kPa and 25°C. The nitrogen is ...

A: Given, Mass of Nitrogen (m) = 2.2 Kg P1 = 100kPa T1 = 25°C=25+273=298K PV1.3 = Constant    

Q: W hen a force F is applied to the handle of the valve shown, its moments about the x and .;. axes ar...

A: Write the expression of the moment about O; Write the position vector;    

Q: Describe the variation of gage pressure with depth in the gradient zone of the solar pond.

A: Solar ponds are basically the small artificial lakes that have some measurable depths. They are pool...

Q: A 10-mm-diameter rod has a modulus of elasticity of E = 100GPa. If it is 4 m long and subjected to a...

A: Given: The diameter of the rod is d=10 mm The length of the rod is L=4 m The axial load on the rod i...

Q: Knowing that the radius of each pulley is 200 mm and neglecting friction. determine the internal for...

A: Draw the FBD of the bar AE. From the given figure write the expression for the angle θ.

Q: A large vertical dam in the shape of a symmetric trapezoid has a height of 30 m, a width of 20 m at ...

A: Given data:   The height of the symmetric trapezoid is: h = 30 m. The width of the symmetric trapezo...

Q: A superalloy gas turbine component was originally designed to operate at temperatures up to 760°C an...

A: Given data: The initial temperature is, T1 = 760 0C = (760 0C+273) K=1033 K The initial life, t1 = ...

Q: Calculate the critical temperature, pressure, and density of (a) air at 200 kPa, 100°C, and 325 m/s,...

A: Given data: The temperature of the air is Tair=100 degrees The temperature of the helium is Thelium=...

Q: 5-59. The bucket of the backhoe and its contents have a wright of 6 kN and a center of gravity at G ...

A: Draw the FBD of the above problem.  

Q: A pipe of diameter 60 mm is gripped by the stillson wrench shown. Portions AB and DE of the wrench a...

A: Draw the free-body diagram of section ABD. Draw the free-body diagram of the pipe. Draw the free b...

Q: A Diesel cycle has a compression ratio of 22 and begins its compression at 85 kPa and 15°C. The maxi...

A: Process 1-2:Reversible adiabatic compression process   Process 2-3:Constant pressure heat addition p...

Q: Question No. 1 Gaseous carbon dioxide at 1 atm and 300°C is flowing inside a horizontal pipe that ha...

A: The data given is, Velocity, V = 15 m/s Inside diameter, Di = 5.3 cm Inside diameter, Do = 6 cm Th...

Q: What is the internal axial force?

A: Internal Axial Force is defined as the force acting in the direction parallel to the axis of the mem...

Q: The wood beam has an allowable shear stress of tallow = 7 MPa. Determine the maximum shear force V t...

A: Given data: *The allowable shear stress σall=7 MPa. *The total length of the section is B=200 mm. *T...

Q: Water fl ows down a rectangular channel that is 4 ft wideand 2 ft deep. The fl ow rate is 20,000 gal...

A: Step 1: The width of the channel is w = 4 ft The depth of the channel is d = 2 ft The flow rate in ...

Q: Solve Prob. 6.67 assuming that the 9-kip load has been removed.(Reference to Problem 6.67):The diago...

A: Given Structure supported with simply supported fix and a roller fix. Applied forces 6 kip, 12 kip T...

Q: Initially, the car travels along a straight road with a speed of 35 m/s. If the brakes are applied a...

A: Given: The initial speed of the car is U=35 m/s The final speed of the car is V=10 m/s The time for ...

Q: P7-5. The lever is held to the fixed shaft using the pin AB. If the couple is applied to the lever, ...

A: Click to see the answer

Q: Solve Prob. 6.24 assuming that the cables hanging from the right side of the tower have fallen to th...

A: Given data  

Q: 6-54. Locate the center of mass of the assembly. The assembly consists of a cylindrical center core,...

A: Calculate the masses of each part A, B and C separately and their respective z coordinate separately...

Q: How do you calculate the maximum bending moment that a beam can resist?

A: The maximum bending moment that a beam can resist is also known as Moment of resistance (MR). Moment...

Q: Figure Q5 shows a steel bar of cross sectional area of 6.5 cm2 and which is acted by forces of Q = 5...

A: Consider the axial load diagram of the member as shown below.

Q: A Brayton cycle with regeneration using air as the working fluid has a pressure ratio of 7. The mini...

A: Given data:   The pressure ratio of the cycle is: r = 7. The minimum temperature of the cycle is: T1...

Q: Saturated steam coming off the turbine of a steam power plant at 40°C condenses on the outside of a ...

A: Given: The mass flow rate of the steam is m=70 kg/h The outer diameter of the tube is D=3 cm The len...

Q: For the beam and loading shown, determine the range of the distance a for which the reaction at B do...

A: Assuming reaction RB positive when directed upwards Taking net moment about D  

Q: Air flows at high speed through a Herschel venturi monitoredby a mercury manometer, as shown in Fig....

A: Given data, Determine the density of fluid by using the ideal gas equation,

Q: Len is asked to design a small water pump for an aquarium. The pump should deliver 18.0 Lpm of water...

A: The specific speed of the pump is written as,  

Q: 15-98. Determine the angular momentum H, of the 3-kg particle about point O. 3 kgoA 6 m/s 2 m 2 m 2 ...

A: Given data: *The mass of the particle at A is m=3 kg. *The velocity of the particle is v=6 m/s. The ...

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings. Determine the ...

A: The torque acting at A is given as : Polar moment of inertia is calculated as :  

Q: Can the entropy of an ideal gas change during an isothermal process?

A: Yes, the entropy of an ideal gas can change during an isothermal process. The entropy of a system ch...

Q: *15-48. Blocks A and B have masses of 40 kg and 60 kg, respectively. They are placed on a smooth sur...

A: Given data: Stretch of the spring, s = 2 m Stiffness of the spring , k = 180 N/m mA = mass of block ...

Q: F7-3. Determine the internal normal force, shear force, and bending moment at point C in the beam. 2...

A: Draw the FBD of the given problem. Apply equilibrium condition. Determine the moment about point B.