SITUATION 6 : A shaft is subjected to a torque of 16kN-m. The maximum permissible stress in the material of theshaft is 65 MPa.13. Find the diameter of the solid shaft.a. 134.28 MPab. 111.90 MPac. 107.83 MPad. 115.32 MPa14. Find the external diameter of a hollow circular shaftif the thickness is 10% of the internal diameter.a. 134.28 MPab. 111.90 MPac. 107.83 MPad. 115.32 MPa15. A hollow circular shaft of thickness 5mm has totransmit 400 kW at 250 rpm. Determine the externaldiameter of the shaft given that the maximum shearstress cannot exceed 60 MPa.a. 197 mmb. 187 mmc. 205 mmd. 192 mm16. A shaft has to transmit a torque of 30 kN-m. Themaximum shear stress is not to exceed 100 MPa and theangle of twist is not to exceed 1/meter length. G = 80GPa. Design the shaft according to the givenspecifications if it is a solid circular shaft.a. 129.87 mmb. 152.80 mmc. 121.63 mmd. 115.18 mm

Answered: Image /qna-images/answer/ff91d24b-ea90-478f-828d-a3076d8cb43a.jpg

SITUATION 6: A shaft is subjected to a torque of 16kN- m. The maximum permissible stress in the material of the shaft is 65 MPa. 13. Find the diameter of the solid shaft. a. 134.28 MPa b. 111.90 MPa c. 107.83 MPa d. 115.32 MPa 14. Find the external diameter of a hollow circular shaft if the thickness is 10% of the internal diameter. a. 134.28 MPa b. 111.90 MPa c. 107.83 MPa d. 115.32 MPa

SITUATION 6: A shaft is subjected to a torque of 16kN- m. The maximum permissible stress in the material of the shaft is 65 MPa. 13. Find the diameter of the solid shaft. a. 134.28 MPa b. 111.90 MPa c. 107.83 MPa d. 115.32 MPa 14. Find the external diameter of a hollow circular shaft if the thickness is 10% of the internal diameter. a. 134.28 MPa b. 111.90 MPa c. 107.83 MPa d. 115.32 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow shaft shown with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P = 75 kN and torques TB = 16 kN-m and TC = 7 kN-m. 14. Calculate the polar moment of inertia of the section in mm4.1 15. Calculate the absolute value of the internal torque at H in kN.m. 16. Calculate the torsional shear stress at H in MPa. 17. Calculate the absolute value of the minor principal stress at point H in MPa. 18. Calculate the absolute value of the major principal stress at point H in MPa. 19. Calculate the absolute value of the maximum shear stress at point H in MPa. 20. Calculate the orientation of the principal axes in degrees. Kindly answer all numbers with complete solution
Very very Urgent The distributed load q and the singular moment M act on the stepped shaft given in the figure. Draw the cross-sectional influence diagrams of the system under these forces. Determine the maximum stress value for the critical section. L1 = 226 mm ,L2 = 118 mm, a = 159 mm M = 572 N.m, q = 5 N/mm D = 51 mm , d1 = 19mm , d2 = 5 mm
Proposed exercise N ° 01 Find the angle of torsion of the free end with respect to the fixed end of the system in the figure. The material is steel and the dimensions are in cm. Proposed exercise N ° 2 Find the length that a hollow steel bar of D = 1.5cm and d = 0.5cm in diameters must have for its ends to rotate 30 ° relative to each other. An allowable shear stress of 713.8 kg / cm2 must not be exceeded, and G = 8.1573x105 kg / cm2
A hollow steel shaft 2660mm long is to be designed to transmit a torque of 24809kJ. Theshear modulus of elasticity, G = 82,740 GPa for steel. The total angle of twist of the lengthof the shaft is must not exceed 6 degrees. And the shear stress in the shaft must notexceed 110.32 MPa. What would be the ratio of the outside diameter to inside diameter?
The following beam is supported by an aluminum bar at C, a steel bar at B, and a brass bar at D. The distance b is equal to 50 mm. The data is shown in the table:If the maximum rotation that can occur at point A is 0.25 radians clockwise, determine: a. The maximum force P that can be applied. Answ: 28347.97 kNb. The normal stress in the aluminum, steel, and brass bars. Answ: 25 000 MPa, 17500 MPa, 25937.5 MPa
From the given figure below and its properties, calculate the stress at the top where the maximum moment is located. (MPa) Properties: Beam width = 207 mmBeam height = 386 mmWLL = 12.48 kN/mWDL = 15.26 kN/mSpan of the beam = 8 mPrestressing force = 293 kNeccentricity = 135 mm
THE ANSWER MUST BE IN FOUR DECIMAL PLACES the steef shaft shown in figure rotates at 4Hz with 35 KW taken off at A, 20 kW removed at B and 55 kW applied at C. Using G=83 GPa, find the maximum shearing stress and the angle of rotation of gear A relative to gear C
The same torque is applied to two tubes with identical metal sheets, determine the ratio of circle/square of the shear stresses. Given: r = 13 mm, S = 22 mm, and t = 2.85 mm.
Find the length that a solid steel shaft of diameter d = 13 mm must have for its ends to rotate 90º with respect to each other. An allowable shear stress of Sy ’= 713.8 kg / cm2, and G = 8.1573x10 ^ 5 kg / cm2 must not be exceeded
A solid constant-diameter circular shaft is subjected to the torques of TA = 490 lb·ft, TB = 1080 lb·ft, TC = 830 lb·ft, and TD = 240 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6. (b) If the allowable shear stress in the shaft is 7400 psi, what is the minimum acceptable diameter for the shaft?
A shaft 100mm in diameter and 3m long, with bult-in ends, is subjected to a clockwise torque of 4KN-m applied 1m from the left end, and to another clockwise torque of 16 KN-m applied 2m fromthe left end. 16. Compute for the shearing stress at segment AB. A. 61.12 MPa B. 20.37 MPa C. 40.74 MPa D. 30.30 MPa 17. Compute for the shearing stress at segment BC. A. 61.12 MPa B. 20.37 MPa C. 40.74 MPa D. 30.30 MPa 18. Compute for the shearing stress at segment CD. A. 61.12 MPa B. 20.37 MPa C. 40.74 MPa D. 30.30 MPa
A hollow steel (E= 30,000ksi) tube (1) with an outside diameter of 2.75in. and a wall thickness of 0.25in. is fastened to a solid aluminum (E= 10,000 ksi) rod (2) that has a 2in. diameter and a solid 1.375in. diameter aluminum rod (3). The bar is loaded as shown in the figure. Determine (a) the change in length of steel tube (1); (b) the deflection of joint D with respect to the fixed support A. (c) the maximum normal stress in the entire axial assembly.