A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross-sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, acompressive normal strain of 480 µɛ is measured from a strain gage located at c = 5 mm below the topmost edge of the tee stem atsection 1-1. What is the applied load P?%3D3PStrain gaged.H.a.b.Answer:i! N

small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The ectional dimensions of the tee shape are b= 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, an ompressive normal strain of 480 e is measured from a strain gage located at c = 5 mm below the topmost edge of the tee s ection 1-1. What is the applied load P? 3P Strain gaga

small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The ectional dimensions of the tee shape are b= 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, an ompressive normal strain of 480 e is measured from a strain gage located at c = 5 mm below the topmost edge of the tee s ection 1-1. What is the applied load P? 3P Strain gaga

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E=200 GPa. If the allowable stress in rod CD is 120 MPa, what weight W in kgs can be safely applied?
For a steel plate, whose length (along the y-direction) is very large compared to its width (along the x-direction), the deflected surface is assumed to be cylindrical; the axis of the cylinder is parallel to the length of the plate. At a certain point, the strain in the shorter direction was measured as 0.0066. Taking E =255 x 103 N/mm2, Poisson’s ratio n = 0.3; Calculate the stresses σx & σy.b) Explain why in-plane forces are neglected in the analysis of bending in thin plates
A symmetrical framework consisting of three pin-connected bars is loaded by a forceP (see figure). The angle between the inclined bars and the horizontal is a = 52°. Theaxial strain in the middle bar is measured as 0.036.Determine the tensile stress in the outer bars if they are constructed of a copper alloyhaving the following stress-strain relationship:
For the figure shown below, If the bending working stresses are 15 ksi in tension and 18 in compression, compute the maximum safe value of P in kips
A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside diameter d1= 80mm. The tube is 2.80m long, and the aluminum has a shear modulus of G= 28GPa.a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist, in degrees,when the maximum shear stress is 52MPa?b. What diameter d, in mm, is required for a solid shaft, as shown, to resists the same torque with the same maximum stress?c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?
Compute the stress distribution of the beam shown in the figure at mid-section. Cross-sectional dimensions of the beam is 14in X 40in. If the tensile capacity is 1ksi, comment on stability of the beam.
A beam having a tee-shaped cross section is subjected to equal 18 kN-m bending moments, as shown. Assume bf = 125 mm, tf = 25 mm, d = 185 mm, tw = 20 mm. Find the following: A. The cross-sectional dimensions of the beam are also shown. B. determine the maximum bending stress (positive if tensile and negative if compressive) produced in the cross section. Express your answer in MPa rounded to the nearest tenths. C. determine the bending stress at point H (positive if tensile and negative if compressive). Express your answer in MPa rounded to the nearest hundredths. D. determine the controlling section modulus about the z axis. Express your answer in (103) mm3 rounded to three significant figures. E. determine the moment of inertia about the z axis. Express your answer in (106) mm4 rounded to three significant figures.
Steel cylinder has 200 mm mean diameter with a wall 1 mm thick and 310 mm long. Determine the circumferential and longitudinal stresses that occur on the cylinder if the maximum pressure difference allowed between the inside and outside must not exceed 100 MPa. Determine the effects of three dimensional loading by determine volumetric strain and change in volume for the first steel cylinder. Modulus of elasticity E= (210 GPa), Poisson's ratio 0.30. 7
Defferentiate the following terms; 1.Resilience and proof resilience 2.proof resilience and modulus of resilience B)A solid beam ABC circular in section has varying sections.portion AB is 6m in length and diameter of 250mm while portion BC is 2m in length and section diameter of 100mm.The beam is subjected to a sudden tensile load.if the maximum stress induced is 400MN/m^2.Determine the strain energy stored in the beam.Take E=200GN/m^2