solid, round column with a length of 5 m and a diameter of 50 mm is fixed at one end and is free at the other end. The material’s yield strength is 300 MPa and its modulus of elasticity is 207 GPa. Assuming concentric loading of the column, determine the following: a) The critical load. b) The critical load if the free end is also fixed (i.e., both ends are now fixed)

solid, round column with a length of 5 m and a diameter of 50 mm is fixed at one end and is free at the other end. The material’s yield strength is 300 MPa and its modulus of elasticity is 207 GPa. Assuming concentric loading of the column, determine the following: a) The critical load. b) The critical load if the free end is also fixed (i.e., both ends are now fixed)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.1P: A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel...

See similar textbooks

Similar questions

A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
A cylindrical rod of copper (E = 110 GPa) having a yield strength of 240 MPa is to be subjected to a load of 7770 N If the length of the rod is 330 mm what must be the diameter to allow an elongation of 0.22 mm& ?
A horizontal steel I – beam of cross-sectional area 0.041m2 is rigidly connected to two vertical girders. If the beam was installed when the temperature was 300C, what stress is developed in the beam when the temperature drops to - 300C? (b) Is the ultimate strength of the steel exceeded? (c)What stress is developed if the beam is concrete and has a cross- sectional area of 0.13m2 ? Will it fracture?
A cylindrical rod of copper (E = 110 GPa, 16 ´106 psi) having a yield strength of 240 MPa (35,000 psi) is to be subjected to a load of 6660 N (1500 lbf). If the length of the rod is 380 mm (15.0 in.), what must be the diameter to allow an elongation of 0.50 mm (0.020 in.)?
A cylindrical rod of steel (E = 207 GPa) having a yield strength of 45,000 psi is to be subjected to a load of 11,100 N. If the length of the rod is 20.0 in., what must be the diameter to allow an elongation of 0.38 mm?
A 0.013 m diameter, 0.5 m long cylindrical metal bar is subjected to a compressive force of 8,500 N. This load does not exceed the yield strength of the material. Determine its diameter under this load. You will need some of the following properties of the metal to solve the problem: modulus of elasticity = 207 GPa, Poisson’s ratio = 0.30, yield strength = 180 MPa, tensile strength = 380 MPa, ductility = 23% elongation.
To support a tensile load of 65 kN, a metallic rod with a circular cross section and a length of 0.32 m will be used. It is required that the tension in the bar does not exceed 240 MPa and the maximum elongation is 0.42 mm. What is the minimum rod diameter [m] in these conditions? (Elasticity for metallic bar take the module as 220 GPa).
.A 5-mm thick mild steel plate is used to form a hollow column of 60 mm outside diameter. The column length is 1.2 m. Calculate the crippling load using Johnson’s Parabolic formula. Take modulus of elasticity and yield strength as 206 GPa and 330 MPa, respectively. Assume one end is hinged and the other end fixed.218212 N176745 N930094 N263252 N
A tensile force of 200 KN is applied on a 0.02-m diameter and.2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. Assuming no permanent deformation occurs in that material, the modulus of elasticity (GPa) is?
A 30-cm-long cylindrical rod of red brass (E = 120 GPa) is loaded axially causing the rod to elongate 0.580 mm. If the diameter of the rod is 1.75 cm, what is the load?
If a force of 300 kN is applied to the top of a circular steel bar with a diameter of 150mm and a length of 300mm, reducing the length of the reaxial direction by 0.16mm, and increasing the diameter of the cross section by 0.01mm, what is the modulus of elasticity E and poisson's ratio of the steel rod?
A cylindrical structural element is made of steel. The element must withstand an axial load of 160 kN. Determine the diameter of its cross section so that it does not have plastic deformation. What is the load that this element resists if it is 80 cm long and suffers an elongation of 200 micrometers? Consider an elastic modulus of 200 G Pa. And a yield stress of 340 M Pa. Use a factor of safety of 3/5 with respect to the yield stress.