Solved Problems: Single-Phase TransformersProblem 1A 19.2 KVA, 19200/480-V, 60 Hz, single-phase transformer is tested with the following results:Open-circuit test(measured from Low-voltage side )Voc = 480 VIoc = 1.25 APoc = 160WShort-circuit test(measured from high-voltage side )Vsc = 1150VIsc = 1.00APsc = 190Wa- Calculate and Sketch the equivalent circuit of this transformer when referred to its low-voltageside.The transformer is now loaded: 15 KW load, 0.9 lagging PF, and a load voltage of 450 V.b- Find the voltage on the high-voltage side of the transformer.c- Find the voltage regulation of this transformer.

Answered: Image /qna-images/answer/e766f8e1-e1ce-4d4c-b16e-00e789a4aa3c.jpg

Solved Problems: Single-Phase Transformers Problem 1 A 19.2 KVA, 19200/480-V, 60 Hz, single-phase transformer is tested with the following results: Open-circuit test (measured from Low-voltage side ) Short-circuit test (measured from high-voltage side ) Vsc = 1150V Voc = 480 V Ioc = 1.25 A Isc = 1.00A %3D Poc = 160W Psc = 190W a- Calculate and Sketch the equivalent circuit of this transformer when referred to its low-voltage side. The transformer is now loaded: 15 KW load, 0.9 lagging PF, and a load voltage of 450 V. b- Find the voltage on the high-voltage side of the transformer. c- Find the voltage regulation of this transformer.

Solved Problems: Single-Phase Transformers Problem 1 A 19.2 KVA, 19200/480-V, 60 Hz, single-phase transformer is tested with the following results: Open-circuit test (measured from Low-voltage side ) Short-circuit test (measured from high-voltage side ) Vsc = 1150V Voc = 480 V Ioc = 1.25 A Isc = 1.00A %3D Poc = 160W Psc = 190W a- Calculate and Sketch the equivalent circuit of this transformer when referred to its low-voltage side. The transformer is now loaded: 15 KW load, 0.9 lagging PF, and a load voltage of 450 V. b- Find the voltage on the high-voltage side of the transformer. c- Find the voltage regulation of this transformer.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.16P: A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters:...

See similar textbooks

Similar questions

An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
Consider the single-line diagram of the power system shown in Figure 3.38. Equipment ratings are Generator 1: 1000MVA,18kV,X=0.2perunit Generator 2: 1000MVA,18kV,X=0.2p.u. Synchronous motor 3: 1500MVA,20kV,X=0.2p.u. Three-phase -Y transformers T1,T2,T3,T4,: 1000MVA,500kV,Y/20kV,X=0.1p.u. Three-phase YY transformer T5: 1500MVA,500kV,Y/20kVY,X=0.1p.u. Neglecting resistance, transformer phase shift, and magnetizing reactance, draw the equivalent reactance diagram. Use a base of 100 MA and 500 kV for the 50-ohm line. Determine the per-unit reactances.
Rework Problem 3.14 if the transformer is delivering rated load at rated secondary voltage and at (a) unity power factor, (b) 0.8 power factor leading. Compare the results with those of Problem 3.14. -
Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
How many transformers are needed to make an open-delta connection?
An open-delta three-phase transformer system has one transformer center-tapped to provide a neutral for single-phase voltages. If the voltage from line to center tap is 277 V, what is the high-leg voltage?
Rework Example 3.12 for a+10 tap, providing a 10 increase for the high-voltage winding.
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
Three single-phase transformers, each rated 10MVA,66.4/12.5kV,60Hz, with an equivalent series reactance of 0.1 per unit divided equally between primary and secondary, are connected in a three-phase bank. The high-voltage windings are V-connected and their terminals are directly connected to a 115-kV three-phase bus. The secondary terminals are all shorted together. Find the currents entering the high-voltage terminals and leaving the low-voltage terminals if the low-voltage windings are (a) Y-connected and (b) - connected.
Reconsider Problem 3.64 with the change that now Tb includes both a transformer of the same turns ratio as Ta and a regulating transformer with a 4 phase shift. On the base of Ta, the impedance of the two comp onents of Tb is jO.1 per unit. Determine the complex power in per unit transmitted to the load through each transformer. Comment on how the transformers share the real and reactive pors.