Some N₂ gas is mixed with some O₂ gas, and the sketch below shows a representative sample of the mixture. The total pressure of the mixture is measured,and found to be 0.070 kPa.gasN20₂mole fractioncarbonCalculate the mole fraction and partial pressure of each gas in this mixture. Round your answers to 2 significant digits. You may assume each gas behaves as anideal gas.0nitrogenoxygenkeypartial pressurekPakPahydrogensulfurchlorinex10×Ś

The mole fractions are calculated using the following formulae. Mole fraction of N2=Number of N2…

Some N₂ gas is mixed with some O₂ gas, and the sketch below shows a representative sample of the mixture. The total pressure of the mixture is measured, and found to be 0.070 kPa. gas N₂ 0₂ carbon mole fraction 0 0 nitrogen oxygen key Calculate the mole fraction and partial pressure of each gas in this mixture. Round your answers to 2 significant digits. You may assume each gas behaves as an ideal gas. partial pressure kPa kPa hydrogen sulfur chlorine 0

Some N₂ gas is mixed with some O₂ gas, and the sketch below shows a representative sample of the mixture. The total pressure of the mixture is measured, and found to be 0.070 kPa. gas N₂ 0₂ carbon mole fraction 0 0 nitrogen oxygen key Calculate the mole fraction and partial pressure of each gas in this mixture. Round your answers to 2 significant digits. You may assume each gas behaves as an ideal gas. partial pressure kPa kPa hydrogen sulfur chlorine 0

Chemistry for Engineering Students

4th Edition

ISBN:9781337398909

Author:Lawrence S. Brown, Tom Holme

Publisher:Lawrence S. Brown, Tom Holme

Chapter5: Gases

Section: Chapter Questions

Problem 5.92PAE

See similar textbooks

Similar questions

93 The complete combustion of octane can be used as a model for the burning of gasoline: 2C8H18+25O216CO2+18H2O Assuming that this equation provides a reasonable model of the actual combustion process, what volume of air at 1.0 atm and 25°C must be taken into an engine to burn 1 gallon of gasoline? (The partial pressure of oxygen in air is 0.21 atm and the density of liquid octane is 0.70 g/mL.)
Pressures of gases in mixtures are referred to as partial pressures and are additive. 1.00 L of He gas at 0.75 atm is mixed with 2.00 L of Ne gas at 1.5 atm at a temperature of 25.0 C to make a total volume of 3.00 L of a mixture. Assuming no temperature change and that He and Ne can be approximated as ideal gases, what are a the total resulting pressure, b the partial pressures of each component, and c the mole fractions of each gas in the mix?
Plot the data given in Table 5.3 for oxygen at 0C to obtain an accurate molar mass for O2. To do this, calculate a value of the molar mass at each of the given pressures from the ideal gas law (we will call this the apparent molar mass at this pressure). On a graph show the apparent molar mass versus the pressure and extrapolate to find the molar mass at zero pressure. Because the ideal gas law is most accurate at low pressures, this extrapolation will give an accurate value for the molar mass. What is the accurate molar mass?
How would the use of a volatile liquid affect the measurement of a gas using open-ended manometers vs. closed-end manometers?
perform stoichiometric ca1cu1uions for reactions involving gases as reactants or products.
A collapsed balloon is filled with He to a volume of 12.5 L at a pressure of 1.00 atm. Oxygen, O2, is then added so that the final volume of the balloon is 26 L with a total pressure of 1.00 atm. The temperature, which remains constant throughout, is 21.5 C. (a) What mass of He does the balloon contain? (b) What is the final partial pressure of He in the balloon? (c) What is the partial pressure of O2 in the balloon? (d) What is the mole fraction of each gas?
A 1.000-g sample of an unknown gas at 0C gives the following data: P(atm) V (L) 0.2500 3.1908 0.5000 1.5928 0.7500 1.0601 1.0000 0.7930 Use these data to calculate the value of the molar mass at each of the given pressures from the ideal gas law (we will call this the apparent molar mass at this pressure). Plot the apparent molar masses against pressure and extrapolate to find the molar mass at zero pressure. Because the ideal gas law is most accurate at low pressures, this extrapolation will give an accurate value for the molar mass. What is the accurate molar mass?