In the circuit in the figure, two identical parallel metallic plates are connected to a 100V battery by an identical metallic spring. In the open state, the plates are unloaded, the span d = 4mm and the surface of one plate is 1778 m ^ 2. When the switch is turned off, the distance between the plates is reduced by 0.5 times. What is the spring constant of each spring in units of Newton / meter? kkSΔνŞekildeki devrede, iki özdeş paralel metalik plaka, özdeş metalik yayla100 V'luk bataryaya bağlamıştır. Anahtar açık durumda, plakalar yüksüz,aralarımdaki açıklık d = 4 mm ve bir plakasının yüzeyi 1778 m dir.Anahtar kapatıldığında, plakalar arasındaki uzaklık 0,5 kat azaltılıy or. Herbir yayın yay sabiti Newton/metre biriminde nedir? E, = 9 x 10-12 CNm?a) 160000 b) 20000 c) 10240 d) 2500 e) 1280

Answered: spring constant

Science

Physics

spring constant

Inquiry into Physics

8th Edition

ISBN:9781337515863

Author:Ostdiek

Publisher:Ostdiek

Chapter10: Atomic Physics

Section: Chapter Questions

Problem 41Q

See similar textbooks

Related questions

Q: 10.0 pF 3. In the circuit below each capacitor initially has a charge of magnitude 3.50 nC on its…

A: Given data : Capacitor's initial charge, q=3.50 nC=3.50×10-9 C Energy loss is 80%, ∴Ef=0.2Ei…

Q: Consider the circuit in the diagram, with sources of emf listed below. Randomized Variables E = 22 V…

A: The expression for the Kirchhoff Junction rule, I3=I1+I2 ..... (1) The expression for the…

Q: A capacitor of capacitance C = 1 μF has been charged so that the potential difference between its…

Q: How much total energy is dissipated in 1 hour, when you attach 2, 6 Ω light bulbs in series with…

A: GIVEN- Resistance (R1) = 2 Ω Resistance (R2) = 6 Ω Battery (V) = 12 V Time (t) = 1 hr = 3600 sec.

Q: The switch in this circuit has been closed for a long time; eventually the charge on the capacitor…

Q: 10.0 pF 3. In the circuit below each capacitor initially has a charge of magnitude 3.50 nC on its…

A: The capacitance and the resistance values are given. C1 = 10 pF C2 = 20 pF C3 = 15 pF R = 25 Ω The…

Q: Consider the circuit in the figure. 15 μ 30 µF 100 V 10 μF Switch (a) Suppose the switch is open, as…

A: Here given a circuit diagram with source 100 volt.There given a switch. We have to calculate the…

Q: ℰ1 = 21 V ℰ2 = 46 V ℰ3 = 5.5 V ℰ4 = 43 V a. Find I1 in amps. b. Find I2 in amps. c. Find I3 in…

Q: Consider a circuit shown below with the following parameters, battery voltage V=13 V, the resistors…

A: When the switch is immediately closed, the inductor will behave as a resistor of infinite resistance…

Q: 114. A capacitor of capacitance 15 uF is fully charged and the potential difference across its…

Q: A 60-W incandescent bulb operates at 120 V. How many electrons and coulombs flow through the bulb in…

Q: A bird stands on a DC electric transmission line carrying 4100A that has a cross-sectional radius of…

A: GivenI=4100 Ampered=4 cmR(per meter)=2.5×10-5 ohm per meterLet V be the potential difference.

Q: In the circuit of the figure below, ℰ = 3.0 kV, C = 6.0 μF, R1 = R2 = R3 = 0.72 MΩ. With C…

Q: For the circuit in the figure, at t = 0 the switch S is closed with the capacitor uncharged. If C =…

Q: 82. Switch S in is closed at time t 30, to begin charging an initially uncharged capacitance C= 15.0…

A: Solution: Given that C = 15 μF R = 20 ohm

Q: Consider the circuit shown in the figure, where ɛ, = 22.7 V, E, = 12.3 V, and R = 14.0 Q. (Due to…

Q: For the circuit shown in the figure, V = 60 V, C = 20 µF, and R = 0.1O MO. Initially the switch S is…

Q: Using Kirchhoff's rules, find the following. (ℰ1 = 71.0 V, ℰ2 = 61.4 V, and ℰ3 = 78.8 V.) A circuit…

A: ℰ1 = 71.0 V, ℰ2 = 61.4 V, and ℰ3 = 78.8 V

Q: Consider the circuit shown in the figure. S 7.20 (a) What is the current, in amperes, on the 7.2N…

A: since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: The circuit in figure consists of two identical parallel metal plates connecte identical metal…

A: Let c1 = 2 uF, as initial capacitance is not provided in the question

Q: Consider the circuit shown in the figure, where Cı=6.00 µF, C2=3.00 µF, and AV= 20.0 V. Capacitor Ci…

A: Charge stored by capacitor Q =CV

Q: a: C in the above circuit consists of N = 1167 (stacked) quadratic parallel plate capacitors of side…

A: Capacitor: A capacitor consists of two conductors separated by a non-conductive region. The…

Q: For the circuit shown in the figure, C = 12 µF and R = 8.5 MΩ. Initially the switch S is open with…

Q: The output voltage of an amplifier was measured at eight different intervals using the same digital…

A: Given, The output voltage of an amplifier was measured at eight different intervals using the same…

Q: In the circuit shown in the figure the batteries have negligible internal resistance and the meters…

Q: Consider the circuit shown in the following figure (Figure 1) , but with the bar moving to the right…

Q: To get the maximum current, the connection should be in parallel. If you create a parallel…

A: This question is based on Current Electricity topic. The effective Resistance formula for parallel…

Q: For the circuit in the figure, at t = 0 the switch S is closed with the capacitor uncharged. If C =…

A: Given: At time t = 0 switch S is closed. Capacitance, C = 56×10-6F Resistance, R = 4×103 ohm Voltage…

Q: In the circuit shown, there are two resistors, with R = 5.0 k2 and R2 = 10.0 k2, along with a…

Q: A capacitor with capacitance 5 mF charged to a voltage of 10V discharges through a 5 Ω resistance.…

A: Given : C = 5 mF V = 10 V R = 5 Ω

Q: 10.0 pF 3. In the circuit below each capacitor initially has a charge of magnitude 3.50 nC on its…

A: Given C1=15pF C2=20pF C3=10pF R=25 ohm Q0=3.5nC

Q: An aluminum rod has a resistance of 1.590 Ω at 20.0°C. Calculate the resistance of the rod at 102°C…

Q: Consider the circuit shoWn with ɛ1 6.0 V, E2 = 12 V, R1 = 100SN, R2 = 200N, and R3 300N. One point…

Q: Consider the circuit shown with E1= 6.0V,E2=12V, R1=100Ω, R2=200Ω and R3=300Ω. One point of the…

Q: What power is dissipated in a circuit through which 0.12 A flows across a potential drop of 3.0 V?…

A: The power dissipated in a circuit is given by: P= VIV = potential differenceI = currentgiven:V = 3VI…

Q: For the circuit shown in the figure below, the switch S is initially open and the voltage across the…

A: Given: Voltage across capacitor, V=60 V Capacitance, C=22 μF = 22×10-6 F Resistance, R=1.5 MΩ =…

Q: *Chapter 32, Problem 018 GO Z Your answer is partially correct. Try again. The circuit in the figure…

A: Given Data:

Q: What is the emf of the battery?

Q: In the circuit in the figure, two identical parallel metallic plates are connected by an identical…

A: Given data: The area of plate is A=1778 m2. The initial distance between plate is d=4 mm. The final…

Q: The switch S, is closed for a long time in the circuit shown. Then, S, is opened and Sz is closed…

A: Given : ε = 30 V L = 4 mH = 0.004 H R = 5 ohms C = 6 μF = 6 x 10-6 F

Q: Consider the circuit shown, where C=6.0 µF, C2=12 µF, and AV= 20 V. Capacitor G is first charged by…

Q: What are the expected readings of the following in the figure below? (R = 8.00 0, AV = 5.20 V) AV…

A: Apply Kirchhoff’s voltage law in the right-most loop, and solve it as follows. -∆V+V+4.50…

Q: Consider the circuit in the diagram, with sources of emf listed below. Randomized Variables E = 22 V…

A: Using Kirchhoff's law to the upper loop, -5I1+22-0.1I1-20I1+40I2+0.5I2-44=0-25.1I1+40.5I2=22 Using…

Q: For the circuit in the figure, at t = 0 the switch S is closed with the capacitor uncharged. If C =…

A: Given: The emf of the battery is 80 V. The capacitance of the circuit is . The resistance of the…

Q: Consider the circuit given in the figure with V =12 V, C,=1.0 µF, C;=2.0 µF, C;=3.0 µF, C,-4.0 µF.…

A: Given:- The Voltage V =12 V C1 = 1 F, C2= 2 F ,C3 = 3 F and C4 = 4 F Two switch S1 and S2 are…

Q: Consider the circuit in the diagram, with sources of emf listed below. Randomized Variables ℰ1 = 25…

A: Given:

Q: Problem 8: A capacitor of capacitance C = 6 µF has been charged so that the potential difference…

A: C = 6 μF Vo = 205 Volts R = 19500 ohm

Question

In the circuit in the figure, two identical parallel metallic plates are connected to a 100V battery by an identical metallic spring. In the open state, the plates are unloaded, the span d = 4mm and the surface of one plate is 1778 m ^ 2. When the switch is turned off, the distance between the plates is reduced by 0.5 times. What is the spring constant of each spring in units of Newton / meter?

k
k
S
Δν
Şekildeki devrede, iki özdeş paralel metalik plaka, özdeş metalik yayla
100 V'luk bataryaya bağlamıştır. Anahtar açık durumda, plakalar yüksüz,
aralarımdaki açıklık d = 4 mm ve bir plakasının yüzeyi 1778 m dir.
Anahtar kapatıldığında, plakalar arasındaki uzaklık 0,5 kat azaltılıy or. Her
bir yayın yay sabiti Newton/metre biriminde nedir? E, = 9 x 10-12 CN
m?
a) 160000 b) 20000 c) 10240 d) 2500 e) 1280

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

Given: M = 2.25 +- 0.021 rad/s R = 0.180 +- 0.003 m w = 17.5 +- 0.25 rad/s Find the angular momentum L with its uncertainty
What are the attributes of DPN in comparision to standard lithography
Given: A= 3i-4j B=-5i+ 6j+ 2k Find: d) A x B e) angle between A and B
What (X-ray based) analytical technique would you use if you wanted to precisely measure the chemical composition of a small (micron-sized) area in a crystal?
I have the answers for a-c. For a, the answer is 7.29 x 10-3 C. For b, the answer is 656 nm and c is 122 nm. Can you please help with d and e? Thank you.
A proton is traveling with a speed of (8.660+_0.013) x10^5 m/s. With what maximum precision can it's position be ascertained?
A proton is traveling with a speed of (8.660+_0.013) x 10^5 m/s. With what maximum precision can it's position be ascertained?
A=2i-3j+k B=i-4j+xk What should be the value of x so that the angle is 30°?
Estimate the angular spread of a laser beam due todiffraction if the beam emerges through a 3.0-mm-diametermirror. Assume that λ = 694nm What would be the diameter of this beam if it struck (a) a satellite 340 km above the Earth, or (b) the Moon?
X rays from a copper X- ray tube (A =204 pm) were diffracted at an angle of 35 degrees by a crystal of silicon. Assuming first- order diffraction. Assuming ( n=2 in the bragg equation, what is the interplaner spacing (d) in silicon? (A) 219 pm (B) 217 pm (C) 215 pm (D) 213 pm
How much time is needed to measure the kinetic energy of an electron whose speed is 10 m/s with an uncertainty of no more than 0.1 percent? How
CT scanners do not detect details smaller than about 0.5 mm. Is this limitation due to the wavelength of x rays? Explain.