State four advantages of a pre-engaged starter when compared with an inertia type.

Q: What is the function of Relay?

A: Relays are electric switches that use electromagnetism to convert small electrical stimuli into…

Q: the purpose of over load protection on a motor is to protect the

A: Please find my answer in the explatnation below.

Q: The graph for on-off control mode operation is............

A: The graph for on-off control mode operation is

Q: The overshoot and system lag can produce an additional temperature swing as much as

A: The difference between system overshoot and system lag is called temperature swing and it can vary…

Q: In a CNC feed drive, a stepper motor with step angle of 1.8 degree drives a lead screw with pitch of…

A: Given data  Step angle θ= 1.8°  Pitch P= 2mm

Q: Explain what happens if it is operated without a starting rheostat; What else is used instead of the…

A: If a DC motor is operated without rheostat then the probability of danger increases as the motor…

Q: A ⁵ ⁄₁₆ nut driver with a 1 ¼ inch diameter handle is used to install a ½ 24 UNC 2B machine screw…

A: P=5/16 inch D= 1.25 inches D=2r

Q: Which of the following is a symbol of an air motor in both directions with variable capacity is

A: Solution: Symbols for actuators, Air motor, rotation in one direction with fixed capacity Air…

Q: Explain  what is follower mechanism.

A:

Q: I need help drawing an elementary diagram of a fractional horsepower, manual motor starter. When the…

A:

Q: The electrical energy consumed by a motor is inversely proportional to its efficiency.

A: An electric motor is a mechanical device that converts electrical energy into mechanical energy. An…

Q: Which of the following is a symbol of an air motor in one direction with invariable capacity is

A: Given :-  symbol of an air motor in one direction with invariable capacity is

Q: Assume that when the start button is pressed M starter does not energize. List seven possible causes…

A:

Q: What are the three basic types of three-phase motors?

A: Given data : Three phase motors

Q: What is the difference between a pilotduty and a line break overload?

A: When there is too much current passes through the electrical devices then in that case overload…

Q: Which of the following is not part of the starter motor circuit?

A: The  starting system or starter motor circuit used to give initial rotation or crank to the engine…

Q: 4. Describe two type of starting system principles and draw the basic starting circuit

A: The starting system is a combination of mechanical and electrical parts that work together to start…

Q: Problem 5 1. Where and why is a centrifugal switch used in a split-phase motor?

A: According to terms and conditions of bartleby we can only provide 1st part. Thank you!

Q: A three phase induction motor operates with a rotor speed of 1440 rpm and develops a torque of…

A: Expression of power for induction motor can be given as P=2πNT60 P=2π×1440×66.3260 P=10 kW…

Q: Introduction about Pnuematic Control of Double Acting Cylinder Using Counter and Timer

A: illustrating with the examples: Use a 5/2 pneumatically actuated control valve and use limit…

Q: What is an attenuator used for?

A:

Q: .Explain belt driven starters and mention its advantages

A: Belt driven starters A belt driven starter motor system used to start an internal combustion engine.…

Q: What type of motors are used for conveyor system? Explain the operation of conveyorsystem with…

A: AC induction motors are ideal for conveyor systems that operate continuously in one direction. For…

Q: 9. What method of DC Motor Speed control is in the image?

A: DC Series Motor Armature Diverter

Q: What rating is used to find the full-load running current of a torque motor?

A: Given Torque motor To find Rating for full load running current

Q: In speed coontrol of dc motor, the tachogenerator is used as control unit. Select one: O True O…

A: Dc Motor

Q: determine the no. of links that can rotate fully ?

A: Let,the given data is;     s=100mm    p=200mm     l=350mm      q=300mm

Q: The piston rod of a double-acting cylinder is to advance when a 3/2- way push button valve is…

A: As for controlling the speed in pneumatic cylinder which is using the proportion air FA series.…

Q: Define relay

A: Relay is also called an electromagnetic switch. It uses low amperage electrical circuit used to…

Q: 9. The information provided by the Design Letter mentioned on motor's nameplate. a) Motor's running…

A: 9     The motor's nameplate-defined specifications are at rated voltage and frequency, including…

Q: A). At full load of 15 h.p. of totally-enclosed fan cooled type motor has a temperature rise of…

A: Given Data The load is 15 hp The temperature rise after half hour is 25°C The temperature rise…

Q: Home Work: develop a sketch to controlling a servo Motor using a single push bottom as:

A: if else statement to control the servo motor according to the condition. Arduino Uno continuously…

Q: The two types of motors used for hermetic compressorsare _________ and _________.

A: There are basically four types of single-phase motors in use in hermetic assemblies: the permanent…

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.