What rating is used to find the full-load running current of a torque motor?

Q: The refrigerator has light bulb which uses 15 W of power and the refrigerator has a COP of 1.3, what...

A: Note - electricity Cost's  unit consider in $ (since P is not defined) Givenligh bulb  power Q=15W =...

Q: For the series circuit in Fig. (1): a. Find the total resistance RT. b. Determine the source current...

A: a.Here all the resistances are in series connection. hence total resistance is given by RT = R1 + R2...

Q: A hot steam pipe having an inside surface temperature of diameter of 8 cm and a wall thickness of 5....

A:

Q: Calculate the support reaction forces for the above beams. Draw shear and moment diagrams.

A: To find: The reactions at A: Ax = ?,  Ay = ?,   and MA = ? To draw the Shear force diagram and bendi...

Q: A block of wood floats in water with 45 mm projecting above the water’s surface. When placed in glyc...

A:  It is a situation based on static equilibrium of the body in a fluid medium. The weight of the body...

Q: A gas contained in a cylinder is compressed, the work required for compression being 9000 kJ. During...

A: For any process, internal energy can be written as the difference between heat transfer and work tra...

Q: A steel specimen is subjected to a tensile force of 400 kips. If the Poisson's Ratio is 0.20, and th...

A: Given:- F=400kips V= 0.20 E=2.8x107psi  

Q: A gas contained in a cylinder is compressed, the work required for compression being 9000 kJ. During...

A:

Q: A rigid tank containing 0.4m3 of air at 400 kPa and 30oC is connected by a valve to a piston cylinde...

A: Given Initial volume = 0.4 m3 Initial pressure = 400 kPa Initial temperature = 30o C  Final pressure...

Q: Given: A ground steel rod with known diameter d is operating at temperature T. You are designing und...

A:

Q: 4- Single acting single cylinder compressor with diameter (15cm) and stroke length of (22.5cm).The a...

A:

Q: uft loft Soolb 4.

A: Given

Q: Determine the total force and location of centre of pressure on one face of the plate shown in Fig. ...

A: Total force, F=ρgAh¯h¯=2+22=3 mF=0.9×1000  kg/m39.81 m/s2π422-123F=62408.52 N,

Q: Consider the air flow over the wing of a civil airliner flying at M. 0.85 and at an altitude of 10,0...

A:

Q: A pelton wheel is supplied with water under a head of 100 m at the rate 1000 litres/s. The bucket de...

A: Given that, H=100 m; Q=1000 L/s=10001000=1 m3/s ;ϕ=180-160=20° ;u=20 m/s

Q: 4. State 10 mechanical properties and their definition.

A: When we apply external force to the material, mechanical properties define how material will behave ...

Q: State and explain the simple change you would have to make to your FLUENT setup to see a shock in th...

A: Ansys fluent is a cae software package of ansys which uses finite volume method to solve simulation ...

Q: An oil radiator has an outside surface area of 0.18 m2 and operates at a surface temperature of 85 d...

A:

Q: How are stress and performance related?    A. Negatively linear: higher stress leads to lower perf...

A: Both options A and B are correct   If we consider it as a linear relationship option A is correct

Q: ress-strain behavior for the brass specimen shown in Figure 6.12, determine the following: (a) The m...

A: Given Stress Strain graph for brass To find Modulus of elasticity Yield stress at offset of 0.002 Ma...

Q: Block A supporting another block B is pulled along a rough horizontal plane by a horizontal force P....

A:

Q: Tengtns of stay Length of stay is the total of wait and service times. Some longer stays are also ap...

A:

Q: lve the bending stress about points A an

A: Concept:Using the bending equation we can calculate the bending stress,MI=σy=ER

Q: ɪꜱ ꜱᴜʙᴊᴇᴄᴛᴇᴅ ᴛᴏ ᴀ ᴛᴇɴꜱɪʟᴇ ꜰᴏʀᴄᴇ ᴏꜰ 400 ᴋɪᴘꜱ with 10 inch of diameter. ɪꜰ ᴛʜᴇ ᴘᴏɪꜱꜱᴏɴ'ꜱ ʀᴀᴛɪᴏ ɪꜱ 0.20...

A:

Q: A cylinder witha 4-inch bore and 30-inch stroke extends in 7 seconds and moves a 25000 lb load, (a) ...

A:

Q: The Deligne Dam on the Cayley River is built so that the wall facing the water is shaped like the re...

A: The force exerted on the dam by water pressure is 5.156 x 109 N.

Q: Given the following: Cp of Br: 0.226 J/g-K BP of Br: 59 deg C density of Br: 3.12 g/mL Hvap of B...

A: Given:Specific heat of Br, Cp=0.226 J/g-KBoiling point of Br=59o CDensity of Br=3.12 g/mlenthalpy of...

Q: determine: a) the pressure, volume and temperature for each state, b) the work done between 1 and 3,...

A:

Q: The Rankine cycle with one closed feedwater heater (CFWH). Superheated water vapor enters the turbin...

A:

Q: 3- Air compressor compresses (7.8m/min) of air at (27°C) and (100kPa) to (925kPa). Determine the pow...

A:

Q: Your steam has a Data of 5.32 MPa and 325 ℃. Find v, u, h and s.

A:

Q: Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine the m...

A:

Q: Continuous cable ADB runs over a small frictionlesspulley at D to support beam OABC that is partof a...

A: The weight of the bar is, W=1700 lb The allowable stress in the cable ADB is, σc= 18 ksi The allowab...

Q: 8. Explain the procedure for determining the size and mass of a flywheel with the help of a turning ...

A:

Q: What point is I56 ?

A: Answer: The point G represents "I56".  

Q: Determine the total pressure and depth of centre of pressure on a plane rectangular surface of 1 m w...

A:

Q: A prismatic bar is subjected to an axial forcethat produces a tensile stress σθ = 65 u MPa and ashea...

A:

Q: show the steps by steps procedure using Solidworks

A: first, we need to create a drawing as shown in picture 1. Buy revolving this figure about Axis 1 we ...

Q: Determine optimum velocity ?

A: Given: Rotor diameter,d=9 mSpeed,N=2700 rpmNozzle angle,α=300Optimum velocity:    It is defined as t...

Q: Block A supporting another block B is pulled along a rough horizontal plane by a horizontal force P....

A:

Q: 8. Consider an iron bar, of diameter 4 cm and length 1m, with specific heat c = 0.437 J/(g K), densi...

A: The movement of heat down a temperature gradient between two bodies in close physical contact is kno...

Q: E G 100 kN 3 m to 200 kN 3 m B 4 m

A: Force in member BC is 375 kN [Compression] and force in member CG is 125 kN [Tension].

Q: An open tank consists of 3 immiscible liquids, in which the water is at the height of 300 cm, above ...

A:

Q: A furnace is to be designed for a heat duty of 30 x 10° Btu/hr and efficiency of 75%. The furnace is...

A:

Q: Water is contained in a cylinder/piston arrangement fitted with upper stops which limit the volume t...

A:

Q: Consider a fully reversible heat pump operating between TH = 45°C and Tc = 5°C. If W cycle = 203 kJ,...

A:

Q: Given: A part is made of ductile material and subjected to principal stresses ơ1, 02, 03 . It is sta...

A: GIVEN: TO FIND:  

Q: The dimensions of a solid rectangular beam sections (assume solid and homogeneous) are shown below w...

A: GIVEN DATA- A RECTANGULAR CROSS SECTION GIVEN WE HAVE TO FIND MOMENT OF INERTIA FOR ALL GIVEN TABLE ...

Q: Which of the following businesses perform workon only one or two automotive systems?a. Dealershipsb....

A: Specialty shops perform work on only one or two automotive systems because specialty shops specializ...

Q: Watch the Torsion Test Demonstration of Cast Iron and Carbon Steel through the following link: https...

A:

Mount Motor

A mount motor can be termed as an engine mount. Mount motors are essential parts of machines and establish a connection between an engine and chassis. They prevent the engine and chassis from getting damaged and also help to stabilize the engine.